- 您現在的位置：買賣IC網 > PDF目錄3872 > PIC18LF25K22-I/SS (Microchip Technology)MCU 8BIT 32KB FLASH 3.6V 28SSOP PDF資料下載
參數資料
| 型號： | PIC18LF25K22-I/SS |
| 廠商： | Microchip Technology |
| 文件頁數： | 30/71頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 8BIT 32KB FLASH 3.6V 28SSOP |
| 產品培訓模塊： | 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 47 |
| 系列： | PIC® XLP™ 18F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 64MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，HLVD，POR，PWM，WDT |
| 輸入/輸出數： | 24 |
| 程序存儲器容量： | 32KB（16K x 16） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 256 x 8 |
| RAM 容量： | 1.5K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.8 V ~ 3.6 V |
| 數據轉換器： | A/D 19x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 包裝： | 管件 |
| 產品目錄頁面： | 656 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
PIC18(L)F2X/4XK22
DS41412E-page 36
2010-2012 Microchip Technology Inc.
2.5.4
EXTERNAL RC MODES
The external Resistor-Capacitor (RC) modes support
the use of an external RC circuit. This allows the
designer maximum flexibility in frequency choice while
keeping costs to a minimum when clock accuracy is not
required. There are two modes: RC and RCIO.
2.5.4.1
RC Mode
In RC mode, the RC circuit connects to OSC1. OSC2/
CLKOUT outputs the RC oscillator frequency divided
by four. This signal may be used to provide a clock for
external circuitry, synchronization, calibration, test or
other application requirements. Figure 2-8 shows the
external RC mode connections.
FIGURE 2-8:
EXTERNAL RC MODES
2.5.4.2
RCIO Mode
In RCIO mode, the RC circuit is connected to OSC1.
OSC2 becomes a general purpose I/O pin.
The RC oscillator frequency is a function of the supply
voltage, the resistor (REXT) and capacitor (CEXT) values
and the operating temperature. Other factors affecting
the oscillator frequency are:
input threshold voltage variation
component tolerances
packaging variations in capacitance
The user also needs to take into account variation due
to tolerance of external RC components used.
2.6
Internal Clock Modes
The oscillator module has three independent, internal
oscillators that can be configured or selected as the
system clock source.
1.
The
HFINTOSC
(High-Frequency
Internal
Oscillator) is factory calibrated and operates at
16 MHz. The frequency of the HFINTOSC can
be
user-adjusted
via
software
using
the
OSCTUNE register (Register 2-3).
2.
The MFINTOSC (Medium-Frequency Internal
Oscillator) is factory calibrated and operates
at 500 kHz. The frequency of the MFINTOSC
can be user-adjusted via software using the
OSCTUNE register (Register 2-3).
3.
The
LFINTOSC
(Low-Frequency
Internal
Oscillator) is factory calibrated and operates at
31.25 kHz. The LFINTOSC cannot be user-
adjusted, but is designed to be stable over
temperature and voltage.
The system clock speed can be selected via software
using the Internal Oscillator Frequency select bits
IRCF<2:0> of the OSCCON register.
The system clock can be selected between external or
internal clock sources via the System Clock Selection
(SCS<1:0>) bits of the OSCCON register. See
Section 2.11 “Clock Switching” for more information.
2.6.1
INTOSC WITH I/O OR CLOCKOUT
Two of the clock modes selectable with the FOSC<3:0>
bits of the CONFIG1H Configuration register configure
the internal oscillator block as the primary oscillator.
Mode selection determines whether OSC2/CLKOUT/
RA7 will be configured as general purpose I/O (RA7) or
FOSC/4 (CLKOUT). In both modes, OSC1/CLKIN/RA7
is
configured
as
general
purpose
I/O.
See
information.
The CLKOUT signal may be used to provide a clock for
external circuitry, synchronization, calibration, test or
other application requirements.
OSC2/CLKOUT(1)
CEXT
REXT
PIC MCU
OSC1/CLKIN
FOSC/4 or
Internal
Clock
VDD
VSS
Recommended values: 10 k
REXT 100 k
CEXT > 20 pF
Note
1:
Alternate pin functions are listed in
2:
Output depends upon RC or RCIO clock mode.
I/O(2)
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16F887-I/PT | IC PIC MCU FLASH 8KX14 44TQFP |
| PIC16F727-I/P | IC PIC MCU FLASH 8KX14 40DIP |
| PIC18F96J65T-I/PT | IC PIC MCU FLASH 48KX16 100TQFP |
| PIC18F86J65T-I/PT | IC PIC MCU FLASH 48KX16 80TQFP |
| PIC18F66J60T-I/PT | IC PIC MCU FLASH 32KX16 64TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC18LF25K22T-I/ML | 功能描述:8位微控制器 -MCU 32KB Flash 1536B RAM 8B nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18LF25K22T-I/SO | 功能描述:8位微控制器 -MCU 32KB Flash 1536B RAM 8B nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18LF25K22T-I/SS | 功能描述:8位微控制器 -MCU 32KB Flash 1536B RAM 8B nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC18LF25K50-E/ML | 制造商:Microchip Technology Inc 功能描述:32 KB FLASH, 2048 BYTES RAM, 48 MHZ INT. OSC, 25 I/0, PIC18 - Rail/Tube 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 32KB FLASH 28QFN |
| PIC18LF25K50-E/SO | 制造商:Microchip Technology Inc 功能描述:32 KB FLASH, 2048 BYTES RAM, 48 MHZ INT. OSC, 25 I/0, PIC18 - Rail/Tube 制造商:Microchip Technology Inc 功能描述:IC MCU 8BIT 32KB FLASH 28SOIC 制造商:Microchip Technology Inc 功能描述:32 KB Flash, 2048 bytes RAM, 48 MHz Int. Osc, 25 I/0, PIC18 Core, USB 2.0, nanoW |
發布緊急采購，3分鐘左右您將得到回復。