- 您現在的位置：買賣IC網 > PDF目錄3821 > PIC24FJ256GA108-I/PT (Microchip Technology)IC PIC MCU FLASH 256K 80TQFP PDF資料下載
參數資料
| 型號： | PIC24FJ256GA108-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 17/18頁 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 256K 80TQFP |
| 特色產品： | PIC24FJ/33FJ MCUs & dsPIC? DSCs |
| 標準包裝： | 119 |
| 系列： | PIC® 24F |
| 核心處理器： | PIC |
| 芯體尺寸： | 16-位 |
| 速度： | 32MHz |
| 連通性： | I²C，PMP，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，LVD，POR，PWM，WDT |
| 輸入/輸出數： | 69 |
| 程序存儲器容量： | 256KB（85.5K x 24） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 16K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 數據轉換器： | A/D 16x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 80-TQFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 648 (CN2011-ZH PDF) |
| 配用： | 876-1004-ND - PIC24 BREAKOUT BOARD MA240015-ND - BOARD MCV PIM FOR 24F256GA DM240011-ND - KIT STARTER MPLAB FOR PIC24F MCU |
PIC24FJ256GA110 FAMILY
DS80368L-page 8
2008-2011 Microchip Technology Inc.
18. Module: I2C Module (Master Mode)
Under certain circumstances, a module operating
in Master mode may Acknowledge its own com-
mand addressed to a slave device. This happens
when the following occurs:
10-Bit Addressing mode is used (A10M = 1),
and:
the I2C master has the same two upper
address bits (I2CADD<9:8>) as the addressed
slave module.
In these cases, the master also Acknowledges the
address command and generates an erroneous I2C
slave interrupt, as well as the I2C master interrupt.
Work around
Several options are available:
When using 10-Bit Addressing mode, make
certain that the master and slave devices do not
share the same 2 MSBs of their addresses.
If this cannot be avoided:
Clear the A10M bit (I2CxCON<10> = 0) prior to
performing a Master mode transmit.
Read the ADD10 bit (I2CxSTAT<8>) to check
for a full 10-bit match whenever a slave I2C
interrupt occurs on the master module.
Affected Silicon Revisions
19. Module: I2C Module (Slave Mode)
Under certain circumstances, a module operating
in Slave mode may not respond correctly to some
of the special addresses reserved by the I2C
protocol. This happens when the following occurs:
10-Bit Addressing mode is used (A10M = 1),
and
bits, A<7:1>, of the Slave address
(I2CADD<7:1>) fall into the range of the
reserved 7-bit address ranges, ‘1111xxx’ or
‘0000xxx’.
In these cases, the Slave module Acknowledges
the command and triggers an I2C slave interrupt; it
does not copy the data into the I2CxRCV register
or set the RBF bit.
Work around
Do not set bits, A<7:1>, of the module’s slave
address equal to ‘1111xxx’ or ‘0000xxx’.
Affected Silicon Revisions
20. Module: A/D Converter
When using PGEC1 and PGED1 to debug an
application on any 64-pin devices in this family, all
voltage references will be disabled. This includes
VREF+, VREF-, AVDD and AVSS. Any A/D conversion
will always equal 3FFh.
Work around
Use PGEC2 and PGED2 to debug any A/D
functionality.
Affected Silicon Revisions
21. Module: SPIx (Enhanced Buffer Mode)
In Enhanced Master mode, the SRMPT bit
(SPIxSTAT<7>) may erroneously become set for
several clock cycles in the middle of a FIFO transfer,
indicating that the shift register is empty when it is
not. This happens when both SPIx clock prescalers
are set to values other than their maximum
(SPIxCON<4:2> ≠ 000 and SPIxCON<1:0> ≠ 00).
Work around
Configure the module to generate an SPIx event
interrupt whenever the last bit is shifted out of the
shift register (SPIxSTAT<4:2> = 101). When the
SPIxIF flag becomes set, the shift register is
empty.
Affected Silicon Revisions
A3
A5
A6
X
A3
A5
A6
X
Note:
This issue applies only to 64-pin devices
in
this
family
(PIC24FJ256GA106,
PIC24FJ192GA106
and
PIC24FJ128GA106).
A3
A5
A6
X
A3
A5
A6
X
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18F2620-I/SO | IC MCU FLASH 32KX16 28SOIC |
| PIC24FJ256GB106-I/PT | IC PIC MCU FLASH 256K 64-TQFP |
| PIC18LF2480-I/SP | IC PIC MCU FLASH 8KX16 28-DIP |
| PIC18F252-I/SP | IC MCU FLASH 16KX16 EE 28DIP |
| PIC18F252-I/SO | IC MCU FLASH 16KX16 EE 28SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC24FJ256GA108T-I/PT | 功能描述:16位微控制器 - MCU 16B 16 MIPS 256KB RAM 69 I/O RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| PIC24FJ256GA110 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64/80/100-Pin, 16-Bit General Purpose Flash Microcontrollers with Peripheral Pin Select |
| PIC24FJ256GA110-E/PT | 功能描述:16位微控制器 - MCU 256KB Flash 16Kb RAM 85 I/O nanoWatt RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| PIC24FJ256GA110-I/PF | 功能描述:16位微控制器 - MCU 16B 16 MIPS 256KB RAM 85 I/O RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| PIC24FJ256GA110-I/PT | 功能描述:16位微控制器 - MCU 16B 16 MIPS 256KB RAM 85 I/O RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。