參數資料
型號: PIC24HJ128GP204-E/PT
廠商: Microchip Technology
文件頁數: 12/84頁
文件大?。?/td> 0K
描述: IC PIC MCU FLASH 128K 44-TQFP
標準包裝: 160
系列: PIC® 24H
核心處理器: PIC
芯體尺寸: 16-位
速度: 40 MIP
連通性: I²C,IrDA,LIN,PMP,SPI,UART/USART
外圍設備: 欠壓檢測/復位,DMA,POR,PWM,WDT
輸入/輸出數: 35
程序存儲器容量: 128KB(43K x 24)
程序存儲器類型: 閃存
RAM 容量: 8K x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 3.6 V
數據轉換器: A/D 13x10b/12b
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: 44-TQFP
包裝: 托盤
產品目錄頁面: 649 (CN2011-ZH PDF)
配用: 876-1004-ND - PIC24 BREAKOUT BOARD
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
dsPIC33F/PIC24H PROGRAMMING SPECIFICATION
DS70152H-page 2
2010 Microchip Technology Inc.
FIGURE 2-2:
CONNECTIONS FOR THE
ON-CHIP REGULATOR
2.2
Program Memory Write/Erase
Requirements
The program Flash memory on the dsPIC33F/PIC24H
has a specific write/erase requirement that must be
adhered to, for proper device operation. The rule is that
any given word in memory must not be written without
first erasing the page in which it is located. Thus, the
easiest way to conform to this rule is to write all the data
in a programming block within one write cycle. The
programming methods specified in this document
comply with this requirement.
2.3
Pins Used During Programming
The pins that are used for programming are listed in
TABLE 2-1:
PINS USED DURING PROGRAMMING
Note 1: These are typical operating voltages. Refer
operating ranges of VDD and VCAP.
2: It is important for the low-ESR capacitor to
be placed as close as possible to the VCAP
pin.
VDD
VCAP
VSS
dsPIC33F/PIC24H
CEFC
3.3V
Note:
A program memory word can be
programmed twice before an erase, but
only if (a) the same data is used in both
program operations or (b) bits containing
‘1’ are set to ‘0’ but no ‘0’ is set to ‘1’.
Note:
Refer to the specific device data sheet for
complete pin diagrams of the dsPIC33F/
PIC24H devices.
Pin Name
During Programming
Pin Name
Pin Type
Pin Description
MCLR
P
Programming Enable
VDD and AVDD(1)
VDD
P
Power Supply
VSS and AVSS(1)
VSS
P
Ground
VCAP
P
CPU Logic Filter Capacitor Connection
PGEC1
I
Primary Programming Pin Pair: Serial Clock
PGED1
I/O
Primary Programming Pin Pair: Serial Data
PGEC2
I
Secondary Programming Pin Pair: Serial Clock
PGED2
I/O
Secondary Programming Pin Pair: Serial Data
PGEC3
I
Tertiary Programming Pin Pair: Serial Clock
PGED3
I/O
Tertiary Programming Pin Pair: Serial Data
Legend: I = Input
O = Output
P = Power
Note 1: All power supply and ground pins must be connected, including analog supplies (AVDD) and ground
(AVSS).
相關PDF資料
PDF描述
PIC18F4431-I/ML IC PIC MCU FLASH 8KX16 44QFN
PIC18F2320-I/SP IC MCU FLASH 4KX16 EEPROM 28DIP
PIC18F2320-I/SO IC MCU FLASH 4KX16 EEPROM 28SOIC
PIC24HJ64GP504-E/PT IC PIC MCU FLASH 64K 44-TQFP
PIC24HJ128GP506A-I/MR IC PIC MCU FLASH 128KB 64-QFN
相關代理商/技術參數
參數描述
PIC24HJ128GP204-I/ML 功能描述:16位微控制器 - MCU 16B MCU 44LD128KB DMA 40MIPS RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24HJ128GP204-I/PT 功能描述:16位微控制器 - MCU 16B MCU 128KB DMA 40MIPS RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24HJ128GP204T-I/ML 功能描述:16位微控制器 - MCU 16B MCU 44LD128KB DMA 40MIPS RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24HJ128GP204T-I/PT 功能描述:16位微控制器 - MCU 16B MCU 128KB DMA 40MIPS RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24HJ128GP206 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Flash Programming Specification