- 您現在的位置：買賣IC網 > PDF目錄368030 > PIP201-12M-3 (NXP SEMICONDUCTORS) DC-to-DC converter powertrain PDF資料下載
參數資料
| 型號： | PIP201-12M-3 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 穩壓器 |
| 英文描述： | DC-to-DC converter powertrain |
| 中文描述： | 200 A SWITCHING REGULATOR, PQCC68 |
| 封裝： | 10 X 10 MM, 0.85 MM HEIGHT, PLASTIC, SOT-687-1, HVQFN-68 |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 345K |
| 代理商： | PIP201-12M-3 |
Philips Semiconductors
PIP201-12M-3
DC-to-DC converter powertrain
Product data
Rev. 03 — 19 November 2003
16 of 20
9397 750 11942
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
15.2 Rework guidelines
Since the solder joints are largely inaccessible, only the side fillets can be touched
up. If there are defects underneath the package, then the whole package has to be
removed.
The first step in component removal is to reflow the solder joints. It is recommended
that the board is heated from the underside using a convective heater whilst hot air or
gas is directed at the upper surface of the component. Nozzles should be used to
direct the hot air or gas to minimize heating of adjacent components. Excessive
airflow should be avoided since this may cause the package to skew. An airflow
velocity of 15 to 20 liters per minute is usually adequate.
Once the solder joints have reflowed, the component should be lifted off the board
using a vacuum pen.
The next step is to clean the solder pads using solder braid and a blade-style
soldering tool. Finally, the pads should be cleaned with a solvent. The solvent is
usually specific to the type of solder paste used in the original assembly and the
paste manufacturers recommendations should be followed.
16. Mounting
16.1 PCB design guidelines
The terminals on the underside of the package are rectangular in shape with a
rounded edge on the inside. Electrical connection between the package and the
printed-circuit board is made by printing solder paste onto the PCB footprint followed
by component placement and reflow soldering. The PCB footprint shown in
Figure 20
is designed to form reliable solder joints.
The use of solder resist between each solder land is recommended. PCB tracks
should not be routed through the corner areas shown in
Figure 20
. This is because
there is a small, exposed remnant of the leadframe in each corner of the package, left
over from the cropping process.
Good surface flatness of the PCB lands is desirable to ensure accuracy of placement
after soldering. Printed-circuit boards that are finished with a roller tin process tend to
leave small lumps of tin in the corners of each land. Levelling with a hot air knife
improves flatness. Alternatively, an electro-less silver or silver immersion process
produces completely flat PCB lands.
相關PDF資料 |
PDF描述 |
|---|---|
| PIP3102-R | LOGIC LEVEL TOPFET |
| PIP3203-A | TOPFET high side switch |
| PIP3206-R | TOPFET high side switch SMD version |
| PIP8.4 | 7,500 & 15,000 Watt TVS Module |
| PIP208 | 15,000 Watt TVS Module(15，000W,鉗位電壓536V，瞬變電壓抑制器模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIP201-12M-3,518 | 功能描述:IC REG BUCK SYNC ADJ 20A 68HVQFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| PIP202-12M | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC to DC converter powertrain |
| PIP202-12M-2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DC-to-DC converter powertrain |
| PIP202-12M-2 /T3 | 功能描述:直流/直流開關轉換器 TAPE7 MOSFET RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PIP202-12M-2,518 | 功能描述:直流/直流開關調節器 TAPE7 MOSFET RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。