- 您現在的位置：買賣IC網 > PDF目錄69049 > PKF4910API (POWER-ONE INC) 1-OUTPUT 9.9 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PKF4910API |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 9.9 W DC-DC REG PWR SUPPLY MODULE |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 1528K |
| 代理商： | PKF4910API |
4
EN/LZT 146 30 R2A Ericsson Microelectronics AB, October 2000
Thermal Data
Two-parameter model
This model provides a more precise description of the thermal charac-
teristics to be used for thermal calculations.
Thermally the power module can be considered as a component and
the case temperature can be used to characterize the properties. The
thermal data for a power module with the substrate in contact with
the case can be described with two thermal resistances. One from case
to ambient air and one from case to PB (Printed circuit Board).
The thermal characteristics temperature can be calculated from the
following formula:
TPB = (TC–TA)×(Rth C–PB+Rth C–A)/Rth C–A–Pd×Rth C–PB+TA
Where:
Pd:
dissipated power, calculated as PO ×(l/
h–1)
TC:
max average case temperature
TA:
ambient air temperature at the lower side of the power
module
TPB:
temperature in the PB between the PKF connection pins
Rth C-PB: thermal resistance from case to PB under the power
module
Rth C-A:
thermal resistance from case to ambient air
v:
velocity of ambient air
Rth C-PB is constant and Rth C-A is dependent on the air velocity.
Free convection is equal to an air velocity of approx. 0.2 – 0.3 m/s.
See figure below.
Palladium plating is used on the terminal pins. A pin temperature (Tp)
in excess of the solder fusing temperature (+183°C for Sn/Pb 63/37)
for more than 25 seconds and a peak temperature above 195°C, is
required to guarantee a reliable solder joint.
Both pin 1 and pin 9 must be monitored.
No responsibility is assumed if these recommendations are not
strictly followed.
Reflow Soldering Information
The PKF series of DC/DC power modules are manufactured in surface
mount technology. Extra precautions must therefore be taken when
reflow soldering the surface mount version. Neglecting the soldering
information given below may result in permanent damage or signifi-
cant degradation of power module performance.
The PKF series can be reflow soldered using IR, Natural Convection,
Forced Convection or Combined IR/Convection Technologies. The high
thermal mass of the component and its effect on
DT (°C) requires that
particular attention be paid to other temperature sensitive components.
IR Reflow technology may require the overall profile time to be ex-
tended to approximately 8–10 minutes to ensure an acceptable
DT.
Higher activity flux may be more suitable to overcome the increase in
oxidation and to avoid flux burn-up.
The general profile parameters detailed in the diagram, with this ex-
tended time to reach peak temperatures, would then be suitable.
Note! These are maximum parameters. Depending on process varia-
tions, an appropriate margin must be added.
相關PDF資料 |
PDF描述 |
|---|---|
| PKF4910API | 1-OUTPUT 9.9 W DC-DC REG PWR SUPPLY MODULE |
| PKF4610ASI | 1-OUTPUT 6.6 W DC-DC REG PWR SUPPLY MODULE |
| PKF4910ASI | 1-OUTPUT 9.9 W DC-DC REG PWR SUPPLY MODULE |
| PKF4111API | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| PKJ4110EPIPHS | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PKF4918BSI | 制造商:Ericsson 功能描述:PKF MACRODENSTM SERIES, ISOLATED, SURFACE MOUNT, CONVERTER - Bulk 制造商:ERCSON 功能描述: 制造商:ERICSON 功能描述: |
| PKF50B1/4 | 制造商:TE Connectivity 功能描述: |
| PKF50B1/8 | 功能描述:旋鈕和轉盤 QUARATE0.669"W/SKIRT SWITCH KNOB RoHS:否 制造商:Davies Molding 材料:Phenolic 設計:Set Screw 軸尺寸:0.25 in 直徑:3/4 in 顏色:Black 指示器型式:Line |
| PKF5510PI | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:5-6 W DC/DC Power Modules Wide Input Series |
| PKF5510SI | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:5-6 W DC/DC Power Modules Wide Input Series |
發布緊急采購，3分鐘左右您將得到回復。