- 您現在的位置：買賣IC網 > PDF目錄385720 > PLUTO (Mitel Networks Corporation) KPSE 10C 10#20 SKT PLUG PDF資料下載
參數資料
| 型號： | PLUTO |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | KPSE 10C 10#20 SKT PLUG |
| 中文描述： | 雙模式CDMA / AMPS二元基帶接口 |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 139K |
| 代理商： | PLUTO |
9
PLUTO
INITIALISATION
Transmit
On power-up or reset (RESETB) the Tx reconstruction
filters are tuned to give the specified cut-off frequency. This
calibration is internal and requires no external input. The
calibration time is 1ms.
Receive
On power-up or reset (RESETB) an autocalibration algo-
rithm is started which can be used to tune the programmable
filters in Jupiter. (Jupiter is a programmable active filter de-
signed for use in dual mode CDMA/AMPS system -further
details of which can be found in the Jupiter Datasheet). The
autocalibration is also initiated when Pluto is switched into
CDMA mode via FMB control.
When Pluto enters calibration mode the En Test (pin 68)
goes high. A test signal at 364kHz is then generated at the
Vtest output (pin 67). This signal is input to Jupiter which
provides a response which is digitised by the I and Q Rx ADCs.
An output DAC - BAL - (Pin 71) then tunes the Q channel to
match the I and Q channel amplitude via a successive approxi-
mation routine. The test signal is then switched to 728kHz
which is above the required cut off of the filter. DAC outputs,
FC_I and FC_Q are then adjusted to tune the I and Q filters to
the correct amplitude with reference to the in band test signal.
The filter cut off is tuned to 690kHz. Oversampling in the Rx
ADC's ensures sufficient accuracy for the calibration. This
calibration routine takes 26ms and after completion En Test
goes low and the test signal Vtest is disabled. Only the CDMA
filter is tuned, the matching within Jupiter ensures that the FM
(AMPS) filter performance meets specification.
0
-0.8
-4
Relative
Amplitude
(dB)
-5.8
1k
630k
1.25M
10M
Frequency (Hz)
CDMA TX FILTER RESPONSE
0
-0.6
Relative
Amplitude
(dB)
-3.0
10k
29k
100k
Frequency (Hz)
FM TX FILTER RESPONSE
Figure 9 Baseband RX interface circuit
相關PDF資料 |
PDF描述 |
|---|---|
| PM1FDS | Surface Mount Crystals |
| PM1FFS | Surface Mount Crystals |
| PM1FFXX | Surface Mount Crystals |
| PM1FG | Surface Mount Crystals |
| PM1FGS | Surface Mount Crystals |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PLV-025 | 制造商:QUALTEK 制造商全稱:QUALTEK 功能描述:25Watts Single Output LED Driver |
| PLV-025S012 | 功能描述:LED電源 LED DRIVER 25W C/V 12V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 輸出功率額定值: 輸入電壓:220 V to 240 V 輸出端數量:1 輸出電壓（通道 1）:40 V 輸出電流（通道 1）:900 mA 安裝風格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/醫用:Commercial |
| PLV-025S018 | 功能描述:LED電源 LED DRIVER 25W C/V 18V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 輸出功率額定值: 輸入電壓:220 V to 240 V 輸出端數量:1 輸出電壓（通道 1）:40 V 輸出電流（通道 1）:900 mA 安裝風格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/醫用:Commercial |
| PLV-025S024 | 功能描述:LED電源 LED DRIVER 25W C/V 24V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 輸出功率額定值: 輸入電壓:220 V to 240 V 輸出端數量:1 輸出電壓（通道 1）:40 V 輸出電流（通道 1）:900 mA 安裝風格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/醫用:Commercial |
| PLV-025S036 | 功能描述:LED電源 LED DRIVER 25W C/V 36V 80X78X27 RoHS:否 制造商:Cree, Inc. 工作模式:Constant Voltage (CV) 輸出功率額定值: 輸入電壓:220 V to 240 V 輸出端數量:1 輸出電壓（通道 1）:40 V 輸出電流（通道 1）:900 mA 安裝風格:Screw 尺寸:90 mm L x 90 mm W x 37.5 mm H 商用/醫用:Commercial |
發布緊急采購，3分鐘左右您將得到回復。