- 您現在的位置：買賣IC網 > PDF目錄224788 > PM-U24-C3 POSITION, LINEAR SENSOR-THROUGH BEAM, 5mm, 50mA, PANEL MOUNT PDF資料下載
參數資料
| 型號： | PM-U24-C3 |
| 元件分類： | Position, Linear, Photoelectric Sensor |
| 英文描述： | POSITION, LINEAR SENSOR-THROUGH BEAM, 5mm, 50mA, PANEL MOUNT |
| 文件頁數： | 11/12頁 |
| 文件大小： | 485K |
| 代理商： | PM-U24-C3 |
Multi-voltage
Micro
Amplifier
Built-in
PM
Sensor
Mounting
Stand
PM
345
PRECAUTIONS FOR PROPER USE
Refer to p.1135l for general precautions.
PM- 54
PM- 54P
CN-14H
CN-14H-2
0.08 to 0.2 mm2 0.18 to 0.22 mm2
(AWG28 to AWG24) (AWG25 to AWG24)
"0.7 to "1.2 mm "1.2 to "1.52 mm
"0.028 to "0.047 in "0.047 to "0.060 in
Conductor cross-
section area
Wire diameter
Wire insulation
material
Crimping of hook-up connectors CN-14H and CN-14H-2
Cautions in plugging or unplugging a connector
1 Strip the cable sheath 15 mm 0.591 in, or more, and insert the
wires into the connector insertion holes till the wire tips reach
the end.
2 Crimp with the exclusive
hook-up pliers CN-HP.
15 mm 0.591 in or more
Lead wire
(Do not strip the wire insulation.)
Cable sheath
Item
Model No.
Crimping method
Wire diameter
Cable diameter
Conductor cross-section area
Arrangement of connector terminals
Note: Wire at Pin No.1 or 2 as per requirement.
V:
V
1: Output 1 (Light-ON)
(Note)
Power supply
2: Output 2 (Dark-ON)
0 V : 0 V
12
0V
V1
2
0V
1 Insert a connector straight into a
sensor until the connector lug is
locked by the sensor hook.
2 When unplugging, give as much
stress as a connector lug can be
relieved from a hook. Then unplug it.
Hook
Lug
5 N or less
Caution: Be sure to hold a connector
when plugging or unplugging
it. Do not hold a terminal or a
cable when plugging or
unplugging the connector.
Otherwise, it will cause a
poor contact.
Notes: 1) When attaching or detach-
ing the connector fitted with
a cable, make sure to hold
the connector firmly before
proceeding.
Notes: 2) After crimping, do not pull
on the cable.
Prior to using the sensor, affix the cable in a way as to
avoid direct stress on the crimped part.
Soldering (Both connector CN-14 and sensor)
If soldering is done directly on the terminals, strictly
adhere to the conditions given below.
Soldering temperature 260 C 500 F or less
Soldering time
3 sec. or less
Soldering position Refer to the below figure
V1
2 0 V
V1
2 0 V
1.5 mm
0.059 in
Sensor
Connector
Soldering
position
Caution: Make sure to use the exclusive hook-up pliers CN-HP.
Commercially available pliers cannot be used.
Vinyl chloride or soft poly-
ethylene
Do not plug or unplug a connector more than 10
times.
Be sure not to give stress more than 5 N to a ter-
minal of both a connector and a sensor.
If you do not follow the above cautions, it will
cause a poor contact.
Procedures of plugging or unplugging a connector
相關PDF資料 |
PDF描述 |
|---|---|
| PM08-271NK | 1 ELEMENT, 0.27 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| PM08-331NK | 1 ELEMENT, 0.33 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| PM08-391NK | 1 ELEMENT, 0.39 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| PM08-47NK | 1 ELEMENT, 0.047 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| PM08-681NK | 1 ELEMENT, 0.68 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PM-U24P | 制造商:PANASONIC ELECTRIC WORKS - ACSD 功能描述:SENSOR 5MM 5-24VDC PNP 制造商:PANASONIC INDUSTRIAL AUTOMATION SALES 功能描述:SENSOR 5MM 5-24VDC PNP |
| PM-U24-R | 制造商:PANASONIC ELECTRIC WORKS - ACSD 功能描述:SENSOR 5MM 5-24VDC NPN 制造商:PANASONIC INDUSTRIAL AUTOMATION SALES 功能描述:SENSOR 5MM 5-24VDC NPN 制造商:Panasonic Electric Works 功能描述:U-SHAPED MICRO PHOTOELECTRIC SENSOR |
| PM-U25 | 功能描述:SENSOR SLOT NPN 制造商:panasonic industrial automation sales 系列:PM-25 零件狀態:有效 感應距離:0.236"（6mm） 感應方法:可傳導的 輸出配置:NPN - 開路集電極 安裝類型:底座安裝 電流 - 電源:15mA 電壓 - 電源:5 V ~ 24 V 響應時間:20μs 工作溫度:-25°C ~ 55°C（TA） 封裝/外殼:模塊，引線，槽型 標準包裝:1 |
| PMU250A | 制造商:Panduit Corp 功能描述: |
| PMU253B | 制造商:Panduit Corp 功能描述:Call vendor for pricing |
發布緊急采購，3分鐘左右您將得到回復。