- 您現在的位置：買賣IC網 > PDF目錄69061 > PM6675S (STMICROELECTRONICS) 3 A SWITCHING CONTROLLER, QCC24 PDF資料下載
參數資料
| 型號： | PM6675S |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩(wěn)壓器 |
| 英文描述： | 3 A SWITCHING CONTROLLER, QCC24 |
| 封裝： | 4 X 4 MM, LEAD FREE, VFQFPN-24 |
| 文件頁數： | 35/53頁 |
| 文件大?。?/td> | 2632K |
| 代理商： | PM6675S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
Application information
PM6675S
40/53
8.1.1
Inductor selection
Once the switching frequency has been defined, the inductance value depends on the
desired inductor ripple current. Low inductance value means great ripple current that brings
poor efficiency and great output noise. On the other hand a great current ripple is desirable
for fast transient response when a load step is applied.
High inductance brings to good efficiency but the transient response is critical, especially if
VINmin - VOUT is little. Moreover a minimum output ripple voltage is necessary to assure
system stability and jitter-free operations (see Section 8.1.3: Output capacitor selection on
). The product of the output capacitor ESR multiplied by the inductor ripple current
must be taken in consideration. A good trade-off between the transient response time, the
efficiency, the cost and the size is choosing the inductance value in order to maintain the
inductor ripple current between 20 % and 50 % (usually 40 %) of the maximum output
current.
The maximum inductor ripple current,
I
L,MAX , occurs at the maximum input voltage.
Given these considerations, the inductance value can be calculated using the following
expression:
Equation 30
where fSW is the switching frequency, VIN is the input voltage, VOUT is the output voltage and
I
L is the inductor ripple current.
Once the inductor value is determined, the inductor ripple current is then recalculated:
Equation 31
The next step is the calculation of the maximum r.m.s. inductor current:
Equation 32
The inductor must have an r.m.s. current greater than IL,RMS in order to assure thermal
stability.
Then the calculation of the maximum inductor peak current follows:
Equation 33
IL,PEAK is important when choosing the inductor, in term of its saturation current.
IN
OUT
L
OUT
IN
V
I
fsw
V
L
=
MAX
,
IN
OUT
MAX
,
IN
MAX
,
L
V
L
fsw
V
I
=
12
)
I
(
)
I
(
I
2
MAX
,
L
2
MAX
,
LOAD
RMS
,
L
+
=
2
I
MAX
,
L
MAX
,
LOAD
PEAK
,
L
+
=
相關PDF資料 |
PDF描述 |
|---|---|
| PM6681ATR | 0.4 A DUAL SWITCHING CONTROLLER, QCC32 |
| PMA4118HSF/C | 1-OUTPUT 18 W DC-DC REG PWR SUPPLY MODULE |
| PMA4118LSF/B | 1-OUTPUT 14.4 W DC-DC REG PWR SUPPLY MODULE |
| PMA4218GSF/B | 1-OUTPUT 21.6 W DC-DC REG PWR SUPPLY MODULE |
| PMA4118LSF/C | 1-OUTPUT 14.4 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PM6675STR | 功能描述:低壓差控制器 - LDO Complete DDR2/3 Mem Pwr supply controllr RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節(jié): 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6 |
| PM6675TR | 功能描述:低壓差控制器 - LDO High eff SD CNRL RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節(jié): 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6 |
| PM6680 | 功能描述:DC/DC 開關控制器 No Rsense dual StepDwn Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| PM6680_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:No Rsense dual step-down controller with adjustable voltages for notebook system power |
| PM6680A | 功能描述:DC/DC 開關控制器 Dual sync controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發(fā)布緊急采購，3分鐘左右您將得到回復。