參數資料
型號: PMB2307R
廠商: SIEMENS A G
元件分類: PLL合成/DDS/VCOs
英文描述: PLL FREQUENCY SYNTHESIZER, 220 MHz, PDSO16
封裝: PLASTIC, TSSOP-16
文件頁數: 3/28頁
文件大小: 706K
代理商: PMB2307R
PMB 2307R
Semiconductor Group
9
02.96
This is done as follows:
1. Setting of synchronous data acquisition by status 2.
2. Programming of the r-counter, status 1 (optional)-data is being loaded into shadow
registers.
3. Programming of the n- or n/a-counter-data is being loaded into shadow registers, the
EN-signal starts the synchronous loading procedure.
4. Synchronous programming – which means data transfer of all data from the shadow
registers to the data registers – takes place at that point in time when the respective
counter reaches “zero + 1”, the maximum repetition rate for channel change is
therefore f
FI:N.
5. Transfer of status 1 information into the corresponding data register is tied to the
n-counter loading, but follows the loading of the n-data register in the distance of one
n-counter dividing ratio, this guarantees that for example a new PD-current value
becomes valid at the same time when the counters are loaded with the new data.
Synchronous avoids additional phase error caused by programming. Synchronous data
acquisition is of especial advantage, when large steps in frequency are to be made in a
short time. For this purpose a high reference frequency can be programmed in order to
achieve rapid – “rough” – transient response. This method increases the fundamental
frequency nearly by the square route of the reference frequency relation. When rough
lock is achieved, another synchronous data transfer is needed to switch back to the
original channel spacing. A “fine” lock in will finish the total step response. It may not be
necessary to change reference frequency, but it make sense to perform synchronous
data acquisition in any case. Especially for GSM, PCN, DECT, DAMPS, JDC, PHP
systems the synchronous mode should be used to get best performance of the
PMB 2307R.
Standby Condition
The PMB 2307R has two standby modes (standby 1, 2) to reduce the current
consumption.
– Standby 1 switches off the whole circuit, the current consumption is reduced below
1
A.
– Standby 2 switches off the counters, the charge pump and the outputs, only the
preamplifiers stay active.
The standby modes do not affect the port output signal. For the influence on the other
output signals see standby table.
Note:
f
RN, fVN, ΦRN and ΦVN are the inverted signals of fR, fV, ΦR and ΦV.
相關PDF資料
PDF描述
PMB4118HWPP/B 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE
PMB4118HWP 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE
PMB4118NWP/B 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE
PMB4118GWPP 1-OUTPUT 18 W DC-DC REG PWR SUPPLY MODULE
PMB4118GWP/B 1-OUTPUT 18 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PMB2307RV1.1GEG 制造商:Infineon Technologies AG 功能描述:Frequency Synthesizer, 16 Pin, Plastic, TSSOP 制造商:Siemens 功能描述:Frequency Synthesizer, 16 Pin, Plastic, TSSOP
PMB2308 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial-Input Frequency Synthesizer
PMB2309 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial-Input Frequency Synthesizer
PMB2312 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Prescaler/Frequency Divider
PMB2313 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Power 1.1 GHz Prescaler