參數資料
型號： PMC8518TS
廠商： ERICSSON POWER MODULES AB
元件分類： 電源模塊
英文描述： 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE
封裝： ROHS COMPLIANT PACKAGE-6
文件頁數： 20/34頁
文件大小： 951K
代理商： PMC8518TS
Ericsson Internal
PRODUCT SPECIFICATION
2 (6)
Prepared (also subject responsible if other)
No.
ESKEVIN
3/1301-BMR 619 8518 Uen
Approved
Checked
Date
Rev
Reference
SEC/D (Julia You)
ECHWANG
2007-8-16
A
Standard Version with “negative logic”
The RC pin may be used to turn on or turn off the regulator
using a suitable open collector function.
Turn off is achieved by connecting the RC pin to the input
voltage. The regulator will run in normal operation when the
RC pin is left open.
RC
Regulator
condition
Min
Typ
Max
Unit
High level
OFF
1.7
16
V
Open
ON
V
External Capacitors
Required Input Filter:
External input capacitors are required to increase the lifetime
of the internal capacitors. Low ESR ceramics should be used,
the minimum input capacitance is stated below.
PMC 8518T S 1 x 4.7 uF.
Optional Input Filter:
To minimize input ripple and to ensure even better stability
more capacitors can be added, see table below.
Consider the max output power in a given application and
choose sufficient capacitors to obtain desired ripple level.
Make sure that the extra capacitors are placed near the input
pins. The table below is just an example since the board
layout also has effect on the result.
Desired input ripple (mVp-p)
Output
power
150
250
500
0-20 W
2x4.7uF
------
20-40 W
5x4.7uF
2x4.7uF
------
40-50 W
8x4.7uF
4x4.7uF
2x4.7uF
Required output filter:
External output capacitance is also required to reduce the
output ripple and to obtain specified load step response. It is
recommended to use low ESR polymer capacitors or low ESR
ceramic capacitors.
Minimum requirement:
PMC 8518T S 2 x 150 uF. (low ESR polymer type).
This is the output filter used in the verification and a
requirement to meet the specification.
Input And Output Impedance
The impedance of both the power source and the load will
interact with the impedance of the DC/DC regulator. It is most
important to have low characteristic impedance, both at the
input and output, as the regulators have a low energy storage
capability. Use capacitors across the input if the source
inductance is greater than 4.7 uH. Suitable input capacitors
are 22 uF - 220 uF low ESR ceramics.
Maximum Capacitive Load
When powering loads with significant dynamic current
requirements, the voltage regulation at the load can be
improved by addition of decoupling capacitance at the load.
The most effective technique is to locate low ESR ceramic
capacitors as close to the load as possible, using several
capacitors to lower the total ESR. These ceramic capacitors
will handle short duration high-frequency components of
dynamic load changes. In addition, higher values of
capacitors (electrolytic capacitors) should be used to handle
the mid-frequency components. It is equally important to use
good design practice when configuring the DC distribution
system.
Low resistance and low inductance PCB layouts and cabling
should be used. Remember that when using remote sensing,
all resistance (including the ESR), inductance and
capacitance of the distribution system is within the feedback
loop of the regulator. This can affect on the regulators
compensation and the resulting stability and dynamic
response performance.
Very low ESR and high capacitance must be used with care.
A “rule of thumb” is that the total capacitance must never
exceed typically 500-700 uF if only low ESR (< 2 m) ceramic
capacitors are used. If more capacitance is needed, a
combination of low ESR type and electrolytic capacitors
should be used; otherwise the stability will be affected.
The PMC 8000 series regulator can accept up to 5 mF of
capacitive load on the output at full load. This gives <500
uF/A of Io. When using that large capacitance it is important
to consider the selection of output capacitors; the resulting
behaviour is a combination of the amount of capacitance and
ESR.
A combination of low ESR and output capacitance exceeding
E
PMC 8518 series
POL regulator, Input 12 V, Output 10 A/50 W
EN/LZT 146 063 R3A Aug 2007
Ericsson Power Modules AB
Technical Specication
27
相關PDF資料
PDF描述
PME4118TP 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE
PME4118TS 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE
PME4118TSR 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE
PME5218T DC-DC REG PWR SUPPLY MODULE
PME5218TP 1-OUTPUT 21.6 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PMC8518TSN 制造商:Ericsson 功能描述:DC/DC PS SGL-OUT 0.75V TO 5.5V 10A 50W - Tape and Reel
PMC85XP 制造商:NXP Semiconductors 功能描述:MOSFET P-CH 30V SOT1118 制造商:NXP Semiconductors 功能描述:MOSFET, P-CH, 30V, SOT1118 制造商:NXP Semiconductors 功能描述:MOSFET, P-CH, 30V, SOT1118; Transistor Polarity:P Channel; Continuous Drain Current Id:-3.4A; Drain Source Voltage Vds:-30V; On Resistance Rds(on):0.085ohm; Rds(on) Test Voltage Vgs:-4.5V; Threshold Voltage Vgs Typ:-780mV ;RoHS Compliant: Yes
PMC85XP,115 制造商:NXP Semiconductors 功能描述:P-Channel MOSFET with Biased NPN transistor 6-Pin HUSON EP T/R 制造商:NXP Semiconductors 功能描述:PMC85XP/HUSON6/REEL7// - Tape and Reel 制造商:NXP Semiconductors 功能描述:MOSFET P-CH 30V HUSON6 制造商:NXP Semiconductors 功能描述:30V P-channel MOSFET
PMC-8670 制造商:Adlink 功能描述:PMC CPU BOARD DIAGNOSTIC MODULE - Bulk
PMC8818TS 功能描述:DC/DC轉換器 .75-5.5 Vdc 16A Iso Input 8.3-16V 80W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*