參數資料
型號： PMH4518TP
廠商： ERICSSON POWER MODULES AB
元件分類： 電源模塊
英文描述： 1-OUTPUT 55 W DC-DC REG PWR SUPPLY MODULE
封裝： ROHS COMPLIANT, PACKAGE-10
文件頁數： 19/29頁
文件大?。?/td> 677K
代理商： PMH4518TP
Ericsson Internal
PRODUCT SPECIFICATION
3 (7)
Prepared (also subject responsible if other)
No.
SEC/D EPANHON
4/1301-BMR 645
Approved
Checked
Date
Rev
Reference
SEC/D (Linda Zhong)
See end
2006-2-14
B
Soldering Information - Surface mounting
The surface mount version of the product is intended for
convection or vapor phase reflow Pb-free processes. To
achieve a good and reliable soldering result, make sure to
follow the recommendations from the solder paste supplier,
to use state-of-the-art reflow equipment and reflow profiling
techniques as well as the following guidelines.
A no-clean flux is recommended to avoid entrapment of
cleaning fluids in cavities inside of the DC/DC regulator. The
cleaning residues may affect long time reliability and isolation
voltage.
Minimum pin temperature recommendations
Pin number 9 is chosen as reference location for the minimum
pin temperature recommendations since this will be the
coolest solder joint during the reflow process.
SnPb solder processes
For Pb solder processes, a pin temperature (T
PIN) in excess of
the solder melting temperature, (T
L, +183 °C for Sn63/Pb37)
for more than 30 seconds, and a peak temperature of
+210 °C is recommended to ensure a reliable solder joint.
Lead-free (Pb-free) solder processes
For Pb-free solder processes, a pin temperature (T
PIN) in
excess of the solder melting temperature (T
L, +217 to +221 °C
for Sn/Ag/Cu solder alloys) for more than 30 seconds, and a
peak temperature of +235 °C on all solder joints is
recommended to ensure a reliable solder joint.
Maximum regulator temperature requirements
To avoid damage or performance degradation of the product,
the reflow profile should be optimized to avoid excessive
heating. The maximum product temperature shall be
monitored by attaching a thermocoupler to the top of the
main transformer.
A sufficiently extended preheat time is recommended to
ensure an even temperature across the host PCB, for both
small and large devices. To reduce the risk of excessive
heating is also recommended to reduce the time in the reflow
zone as much as possible.
SnPb solder processes(PENDING)
For conventional SnPb solder processes, the product is
qualified for MSL 1 according to IPC/JEDEC standard
J-STD-020C.
During reflow, T
P must not exceed +225 °C at any time.
Lead-free (Pb-free) solder processes
For Pb-free solder processes, the product is qualified for
MSL 3 according to IPC/JEDEC standard J-STD-020C.
During reflow, T
P must not exceed +260 °C at any time.
25 °C
Time
Temperature
Ramp-down
(cooling)
Ramp-up
Reflow
Preheat
Time 25 °C to peak
T
P
T
L
Profile features
Sn/Pb eutectic
assembly
Pb-free assembly
Average ramp-up rate
3 °C/s max
Solder melting
temperature (typical)
T
L
+183 °C
+221 °C
Peak product temperature T
P
+225 °C
+260 °C
Average ramp-down rate
6 °C/s max
Time 25 °C to peak
temperature
6 minutes max
8 minutes max
PIN 9 for measurement of
minimum solder joint
temperature, T
PIN
Main transformer for
measurement of Max
product temperature, T
P
E
PMH 4000 series
POL regulator, Input 2.95-3.65 V, Output 22 A/55 W
EN/LZT 146 322 R1B February 2006
Ericsson Power Modules AB
Technical Specication
E
PMH 4000 series
POL regulator, Input 2.95-3.65 V, Output 22 A/55 W
EN/LZT 146 322 R1B April 2006
Ericsson Power Modules AB
Technical Specication
26
相關PDF資料
PDF描述
PMH8318TS 1-OUTPUT 32.4 W DC-DC REG PWR SUPPLY MODULE
PMH8318TSR 1-OUTPUT 32.4 W DC-DC REG PWR SUPPLY MODULE
PMH8318TP 1-OUTPUT 32.4 W DC-DC REG PWR SUPPLY MODULE
PMH8918LSR 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE
PMH8918LP 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PMH4518TS 功能描述:DC/DC轉換器 .8-2.5 Vdc 22A Iso Input 3.3V 55W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PMH4518TSR 功能描述:DC/DC轉換器 0.8-2.5V 22A Non-Iso Input 3.3V 55W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PMH5718TP 功能描述:DC/DC轉換器 0.8-3.6V 22A Non-Iso Input 5V 79.2W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PMH5718TS 功能描述:DC/DC轉換器 .8-3.6 Vdc 22A Iso Input 5V 79.2W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PMH5718TSR 功能描述:DC/DC轉換器 0.8-3.6V 22A Non-Iso Input 5V 79.2W RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*