參數資料
型號： PN22N*
英文描述： 10A High Efficiency DC/DC µModule; Package: LGA; No of Pins: 104; Temperature Range: -40°C to +85°C
中文描述： Monitor_ICs：XC62FP3302 61CC4202 KA555D/TR RYC8220 - 200萬FST3257 52742 S5D2501E19 - D0 52324 33262 TDA16850 7045
文件頁數： 17/98頁
文件大?。?/td> 2244K
4-3-4 (d)WHITE BALANCE ADJUSTMENT VERIFICATION
Refer to the procedure for 9300K, section 4-3-2 (d).
4-3-5 Luminance Uniformity Check
Luminance is considered uniform only if the ratio
of lowest to highest brightness areas on the screen
is not less than 7.5:10.
CONDITIONS
Scanning frequency:
91 kHz/ 85 Hz
(1280 x 1024)
White flat field
395 (H) x 296 (V)
Cut off point
Maximum
Display image:
Display size
Brightness:
Contrast:
PROCEDURE
Measure luminance at nine points on the display
screen (see figure below).
4-3-6 Focus Adjustment
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
91 kHz/ 85 Hz
“H” character pattern
Cut off point
Maximum
PROCEDURE
1.
Adjust the Focus VR on the FBT to display the
sharpest image possible.
2.
Use Locktite to seal the Focus VR in position.
4-3-7 Color Purity Adjustment
Color purity is the absence of undesired color.
Conspicuous mislanding (unexpected color in a
uniform field) within the display area shall not be
visible at a distance of 50 cm from the CRT
surface.
CONDITIONS
Orientation:
Scanning frequency:
Display image:
Luminance:
Monitor facing east
91 kHz/ 85 Hz
Green flat field
Cut off point at the center
of the display area
Note:
Color purity adjustments should only be
attempted by qualified personnel.
PROCEDURE
For trained and experienced service technicians
only.
Use the following procedure to correct minor
color purity problems:
1.
Make sure the display is not affected by
external magnetic fields.
Very carefully break the glue seal between the
2-pole purity convergence magnets (PCM), the
band and the spacer.
Make sure the spacing between the PCM
assembly and the CRT stem is 29 mm ± 1 mm.
Display a green pattern over the entire display
area.
Adjust the purity magnet rings on the PCM
assembly to display a pure green pattern.
(Optimum setting: x = 0.295 ± 0.015,
y = 0.594 ± 0.015)
Repeat steps 4 and 5 using a red pattern and
then again, using a blue pattern.
2.
3.
4.
5.
6.
Table 4-2. Color Purity Tolerances
(For 9300K color adjustment: x = 0.283 ±0.02, y = 0.298 ±0.02)
7.
When you have the PCMs properly adjusted,
carefully glue them together to prevent their
movement during shipping.
4 Alignment and Adjustments
PN22N*
4-7
Red:
x = 0.620 ±0.015
y = 0.334 ±0.015
Green:
x = 0.289 ±0.015
y = 0.595 ±0.015
Blue:
x = 0.153 ±0.015
y = 0.072 ±0.015
Figure 4-10 Lumnance Uniformty Check Locations
相關PDF資料
PDF描述
PN2484 NPN General Purpose Amplifier
PN2484 LOW LEVEL, LOW NOISE NPN SILICON PLANAR TRANSISTORS
PN2484 Small Signal Transistors
PN2906 PNP SILICON GENERAL PURPOSE AMPLIFIERS AND SWITCHES
PN2906A PNP SILICON GENERAL PURPOSE AMPLIFIERS AND SWITCHES
相關代理商/技術參數
參數描述
PN22SJ03QE 制造商:C&K Components 功能描述:PN22SJ03QE
PN22SJNA03QE 功能描述:按鈕開關 DPDT PUSHBUTTON RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
PN22SJSA03QE 功能描述:按鈕開關 Shorting Push Button Switch Dpdt RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0
PN2304PB005 制造商:Hubbell Wiring Device-Kellems 功能描述:LINKOSITY 20A SNIG MALE R/A CABLE 5'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*