參數(shù)資料
型號: PPC405EP-3GB266C
廠商: APPLIEDMICRO INC
元件分類: 微控制器/微處理器
英文描述: PowerPC 405EP Embedded Processor
中文描述: 32-BIT, 266.66 MHz, RISC PROCESSOR, PBGA385
封裝: 31 X 31 MM, PLASTIC, EBGA-385
文件頁數(shù): 29/50頁
文件大?。?/td> 373K
代理商: PPC405EP-3GB266C
PPC405EP – PowerPC 405EP Embedded Processor
Revision 1.07 – September 10, 2007
Data Sheet
AMCC
29
Signal List
The following table provides a summary of the number of package pins associated with each functional interface
group.
In the table “Signal Functional Description” on page 31, each external signal is listed along with a short description
of the signal function. Active-low signals (for example, RAS) are marked with an overline. Please see “Signals
Listed Alphabetically” on page 13 for the pin (ball) number to which each signal is assigned.
Multiplexed Pins
Some signals are multiplexed on the same package pin (ball) so that the pin can be used for different functions. In
most cases, the signal names shown in this table are not accompanied by signal names that may be multiplexed
on the same pin. If you need to know what, if any, signals are multiplexed with a particular signal, look up the name
in “Signals Listed Alphabetically” on page 13. It is expected that in any single application a particular pin will always
be programmed to serve the same function. The flexibility of multiplexing allows a single chip to offer a richer pin
selection than would otherwise be possible.
In addition to multiplexing, many pins are also multi-purpose. For example, in the PCI interface PCIC3:0/BE3:0
serves as both Command and Byte Enable signals. In this example, the pins are also bidirectional, serving as both
inputs and outputs.
Initialization Strapping
One group of pins is used as strapped inputs during system reset. These pins function as strapped inputs only
during reset and are used for other functions during normal operation (see “Initialization” on page 48). Note that the
use of these pins for strapping is not considered multiplexing since the strapping function is not programmable.
Pull-Up and Pull-Down Resistors
Pull-up and pull-down resistors are used for strapping during reset and to retain unused or undriven inputs in an
appropriate state. The recommended pull-up value of 3k
Ω
to +3.3V (10k
Ω
to +5V can be used on 5V tolerant I/Os)
and pull-down value of 1k
Ω
to GND, applies only to individually terminated signals. To prevent possible damage to
the device, I/Os capable of becoming outputs
must never
be tied together and terminated through a common
resistor.
If your system-level test methodology permits, input-only signals can be connected together and terminated
through either a common resistor or directly to +3.3V or GND. When a resistor is used, its value must ensure that
the grouped I/Os reach a valid logic zero or logic one state when accounting for the total input current into the
PPC405EP.
Table 5. Pin Summary
Group
No. of Pins
215
33
248
Non multiplexed
Multiplexed
Total Signal Pins
OV
DD
V
DD
Gnd
Thermal (and Gnd)
Reserved
Total Pins
43
16
53
25
0
385
相關PDF資料
PDF描述
PPC405EP-3GB266CZ PowerPC 405EP Embedded Processor
PPC405EP-3GB333C PowerPC 405EP Embedded Processor
PPC405EP-3GB333CZ PowerPC 405EP Embedded Processor
PPC405EP-3LB133C PowerPC 405EP Embedded Processor
PPC405EP-3LB133CZ PowerPC 405EP Embedded Processor
相關代理商/技術參數(shù)
參數(shù)描述
PPC405EP-3GB266CZ 制造商:AppliedMicro 功能描述:MPU 405EP RISC 32-Bit 0.18um 266MHz 3.3V 385-Pin EBGA T/R
PPC405EP-3GB333C 制造商:AppliedMicro 功能描述:MPU 405EP RISC 32-Bit 0.18um 333MHz 3.3V 385-Pin EBGA Tray 制造商:AMCC 功能描述:MPU 405EP RISC 32BIT 0.18UM 333MHZ 3.3V 385PIN EBGA - Trays
PPC405EP-3GB333CZ 制造商:AppliedMicro 功能描述:MPU 405EP RISC 32-Bit 0.18um 333MHz 3.3V 385-Pin EBGA T/R
PPC405EP-3LB133C 制造商:AppliedMicro 功能描述:MPU 405EP RISC 32-Bit 0.18um 133MHz 3.3V 385-Pin EBGA Tray 制造商:AMCC 功能描述:MPU 405EP RISC 32BIT 0.18UM 133MHZ 3.3V 385PIN EBGA - Trays 制造商:AMCC 功能描述:AMCPPC405EP-3LB133C 32 Bit PowerPC
PPC405EP-3LB133CZ 制造商:AppliedMicro 功能描述:MPU 405EP RISC 32-Bit 0.18um 133MHz 3.3V 385-Pin EBGA T/R