• <rt id="lxp7i"></rt>
  • <nobr id="lxp7i"><strike id="lxp7i"></strike></nobr>
    參數資料
    型號: PSD302-25JM
    廠商: 意法半導體
    英文描述: Low Cost Field Programmable Microcontroller Peripherals
    中文描述: 低成本現場可編程微控制器外圍設備
    文件頁數: 36/85頁
    文件大?。?/td> 691K
    代理商: PSD302-25JM
    PSD3XX Famly
    33
    All the inputs shown, except CSI, go to the PAD logic. These signals must be taken into
    consideration when calculating the composite frequency. Before we make the calculation,
    let’s establish the following conditions:
    The input with the highest frequency is ALE, which is 2 MHz. So our base period is
    500 nsec for this example.
    Only the address information from the multiplexed signals AD0-AD7 reach the PAD
    logic because of the internal address latch. Signal transitions from data on AD0-AD7
    do not reach the PADs.
    The three inputs (Int, Sel, or Rdy) change state very infrequently relative to the 80C31
    bus signals.
    Now, lets assume the following is a snapshot in time of all the input signals during a typical
    80C31 bus cycle. We’ll use a code fetch as an example since that happens most often.
    16.0
    Power
    Management
    (cont.)
    ONE TYPICAL 80C31 BUS CYCLE (2 MHz, 500 nsec)
    ALE
    PSEN
    AD0-AD7
    A8-A15
    INT
    SEL
    RDY
    FOUR DISTINCT
    TRANSITIONS
    <25 nsec
    ADDR
    DATA
    1
    2
    3
    The calculation of the composite frequency is as follows:
    There are four distinct transitions (first four dotted lines) within the base period of
    500 nsec. These first four transitions all count toward the final composite frequency.
    The transition at (1) in the diagram does not count as a distinct transition because it is
    within 25 nsec of a neighboring transition (use 50 nsec for a ZPSD3XXV device).
    Transition (2) above does not add to the composite frequency because only the
    internally latched address signals reach the PADs, the data signal transitions do not.
    The transition at (3) just happens to appear in this snapshot, but its frequency is so
    low that it is not a significant contributor to the overall composite frequency, and will
    not be used.
    Divide the 500 nsec base period by the four (distinct transitions), yielding 125 nsec.
    1/125 nsec = 8 MHz.
    Use 8 MHz as the composite frequency of PAD inputs when calculating current
    consumption. (See the next section for a sample current calculation.)
    16.6 Loading on I/Opins
    A final consideration when calculating the current usage for the entire PSD device is the
    loading on I/O pins. All specifications for PSD current consumption in this document
    assume zero current flowing through PSD I/O pins (including ADIO). I/O current is dictated
    by the individual design implementation, and must be calculated by the designer. Be aware
    that I/O current is a function of loading on the pins and the frequency at which the signals
    toggle.
    相關PDF資料
    PDF描述
    PSD302-70J Low Cost Field Programmable Microcontroller Peripherals
    PSD302-70JI Low Cost Field Programmable Microcontroller Peripherals
    PSD302-70JM Low Cost Field Programmable Microcontroller Peripherals
    PSD302-90J Low Cost Field Programmable Microcontroller Peripherals
    PSD302-90JI Low Cost Field Programmable Microcontroller Peripherals
    相關代理商/技術參數
    參數描述
    PSD302-70J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
    PSD302-70JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
    PSD302-70JM 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
    PSD302-70LI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
    PSD302-70LM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral