參數資料
型號： PSD412A2-20JI
英文描述： 30V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a TO-254AA package; A IRHM57Z60 with Standard Packaging
中文描述： 現場可編程外圍
文件頁數： 68/123頁
文件大?。?/td> 657K
代理商： PSD412A2-20JI
PSD4XX Famly
65
The PSD4XX
Architecture
(cont.)
Figure 34. Port A In Peripheral I/OMode
RD
PSEL0
PSEL1
D0 – D7
WR
PA0 – PA7
9.4.5 Peripheral I/O
The Peripheral I/O Mode is one of the operating modes of Port A. In this mode, Port A
is connected to the data bus of peripheral devices. Port A is enabled only when
the microcontroller is accessing the devices, otherwise the Port is tri-stated. This feature
enables the microcontroller to access external devices without requiring buffers and
decoders. Figure 34 shows the structure of Port A in the Peripheral I/O Mode.
The memory address space occupied by the devices are defined by two signals: PSEL0
and PSEL1. The signals are direct outputs from the Decoding PLD (DPLD). Whenever any
of the signals is active, the Port A driver is enabled, and the direction of the data flow is
determined by the RD/WR signals.
The Peripheral I/O Mode and the peripheral select signals are configured and defined in the
PSDsoft Software (see the section on I/O Port for configuration). The PIO bit in the VM
Register (see Table 17) also needs to be set to “1” by the user to initialize the Peripheral I/O
Mode.
The Peripheral I/O mode can be used, for example, in DMA applications where the
microcontroller does not support DMA operations, such as tri-stating the address/data bus.
Figure 35 shows a block diagram of a microcontroller and PSD4XX based design that
makes use of this mode. In this application, the microcontroller has a multiplexed bus which
is connected to the ADIO port. The C and D ports connect to the peripheral address bus
and are both configured in Address Out Mode. Port A is configured in the Peripheral I/O
mode and is connected to the peripheral data bus. Ports B and E are used to generate
control signals.
During normal activity, the microcontroller has access to any peripheral (memory or I/O
device) through the PSD4XX device. When there is a DMA request, the
microcontroller tri-states the address bus on Ports C and D by writing a “0” to the port
Direction Registers. The DMA controller then takes over the data and address buses after
receiving acknowledgement from the microcontroller.
相關PDF資料
PDF描述
PSD412A2-20LI 400V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a SMD-3 package; A IRHNB7360SE with Standard Packaging
PSD412A2-20LM 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a TO-257AA package; Similar to IRHY57230CM with optional Total Dose Rating of 500kRads
PSD412A2-20U 200V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a TO-257AA package; Similar to IRHY57230CM with optional Total Dose Rating of 1000kRads
PSD412A2-20UI Field-Programmable Peripheral
PSD412A2-70J Field-Programmable Peripheral
相關代理商/技術參數
參數描述
PSD412A2-20LI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A2-20LM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A2-20U 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A2-20UI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
PSD412A2-70J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*