參數資料
型號： PSD4235G2-A-70U
廠商： 意法半導體
英文描述： Flash In-System-Programmable Peripherals for 16-Bit MCUs
中文描述： Flash在系統可編程外設的16位微控制器
文件頁數： 21/89頁
文件大?。?/td> 703K
代理商： PSD4235G2-A-70U
21/89
PSD4235G2
Primary Flash Memory and Secondary Flash
memory Description.
The primary Flash memo-
ry is divided evenly into 8 sectors. The secondary
Flash memory is divided evenly into 4 sectors.
Each sector of either memory block can be sepa-
rately protected from Program and Erase cycles.
Flash memory may be erased on a sector-by-sec-
tor basis, and programmed word-by-word. Flash
sector erasure may be suspended while data is
read from other sectors of the block and then re-
sumed after reading.
During a Program or Erase cycle in Flash memory,
the status can be output on the Ready/Busy pin
(PE4). This pin is set up using PSDsoft Express.
Memory Block Select Signals.
The DPLD gen-
erates the Select signals for all the internal memo-
ry blocks (see the section entitled “PLDs”, on page
31). Each of the sectors of the primary Flash mem-
ory has a Select signal (FS0-FS7) which can con-
tain up to three product terms. Each of the sectors
of the secondary Flash memory has a Select sig-
nal (CSBOOT0-CSBOOT3) which can contain up
to three product terms. Having three product terms
for each Select signal allows a given sector to be
mapped in different areas of system memory.
When using a MCU with separate Program and
Data space (80C51XA), these flexible Select sig-
nals allow dynamic re-mapping of sectors from
one memory space to the other before and after
IAP. The SRAM block has a single Select signal
(RS0).
Ready/Busy (PE4).
This signal can be used to
output the Ready/Busy status of the PSD. The out-
put is a 0 (Busy) when a Flash memory block is be-
ing written to,
or
when a Flash memory block is
being erased. The output is a 1 (Ready) when no
Write or Erase cycle is in progress.
Memory Operation.
The primary Flash memory
and secondary Flash memory are addressed
through the MCU Bus Interface. The MCU can ac-
cess these memories in one of two ways:
I
The MCU can execute a typical bus Write or
Read
operation
just as it would if accessing a
RAM or ROM device using standard bus cycles.
I
The MCU can execute a specific instruction that
consists of several Write and Read operations.
This involves writing specific data patterns to
special addresses within the Flash memory to
invoke an embedded algorithm. These
instructions are summarized in Table 29.
Typically, the MCU can read Flash memory using
Read operations, just as it would read a ROM de-
vice. However, Flash memory can only be erased
and programmed using specific instructions. For
example, the MCU cannot write a single byte di-
rectly to Flash memory as one would write a byte
to RAM. To program a word into Flash memory,
the MCU must execute a Program instruction, then
test the status of the Programming event. This sta-
tus test is achieved by a Read operation or polling
Ready/Busy (PE4).
Flash memory can also be read by using special
instructions to retrieve particular Flash device in-
formation (sector protect status and ID).
相關PDF資料
PDF描述
PSD4235G2-A-70UI Flash In-System-Programmable Peripherals for 16-Bit MCUs
PSD4235G2-B-70M Flash In-System Programmable ISP Peripherals For 16-bit MCUs 5V Supply
PSD4235G2-B-70MI CAP 0.47UF 25V 20% TANT SMD-3216-18 TR-7-PL GOLD
PSD4235G2-B-70U Flash In-System-Programmable Peripherals for 16-Bit MCUs
PSD4235G2-B-70UI CAP 0.47UF 25V 20% TANT SMD-3216-18 TR-7-PL SN100%
相關代理商/技術參數
參數描述
PSD4235G2V-12UI 功能描述:CPLD - 復雜可編程邏輯器件 3.3V 4M 120ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD4235G2V-90U 功能描述:CPLD - 復雜可編程邏輯器件 3.3V 4M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD4256G6V-10UI 功能描述:CPLD - 復雜可編程邏輯器件 3.3V 8M 100ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD4-36 制造商:Tamura Corporation of America 功能描述:
PSD-45 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:45W DC-DC Single Output Switching Power Supply
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*