- 您現在的位置：買賣IC網 > PDF目錄368225 > PSD4235G2-A-70UI (意法半導體) Flash In-System-Programmable Peripherals for 16-Bit MCUs PDF資料下載
參數資料
| 型號： | PSD4235G2-A-70UI |
| 廠商： | 意法半導體 |
| 英文描述： | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| 中文描述： | Flash在系統可編程外設的16位微控制器 |
| 文件頁數： | 59/89頁 |
| 文件大?。?/td> | 703K |
| 代理商： | PSD4235G2-A-70UI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
59/89
PSD4235G2
POWER MANAGEMENT
The PSD device offers configurable power saving
options. These options may be used individually or
in combinations, as follows:
I
All memory blocks in a PSD (primary Flash
memory, secondary Flash memory, and SRAM)
are built with power management technology. In
addition to using special silicon design
methodology, power management technology
puts the memories into standby mode when
address/data inputs are not changing (zero DC
current). As soon as a transition occurs on an
input, the affected memory “wakes up”,
changes and latches its outputs, then goes back
to standby. The designer does
not
have to do
anything special to achieve memory Stand-by
mode when no inputs are changing—it happens
automatically.
The PLD sections can also achieve Stand-by
mode when its inputs are not changing, as de-
scribed for the Power Management Mode Reg-
isters (PMMR), later.
I
The Automatic Power Down (APD) block allows
the PSD to reduce to stand-by current
automatically. The APD Unit also blocks MCU
address/data signals from reaching the
memories and PLDs. This feature is available
on all PSD devices. The APD Unit is described
in more detail in the section entitled “APD Unit”,
on page 60.
Built in logic monitors the Address Strobe of the
MCU for activity. If there is no activity for a cer-
tain period (the MCU is asleep), the APD Unit
initiates Power-down mode (if enabled). Once in
Power-down mode, all address/data signals are
blocked from reaching the PSD memories and
PLDs, and the memories are deselected inter-
nally. This allows the memories and PLDs to re-
main in Stand-by mode even if the address/data
signals are changing state externally (noise,
other devices on the MCU bus, etc.). Keep in
mind that any unblocked PLD input signals that
are changing states keeps the PLD out of
Stand-by mode, but not the memories.
I
PSD Chip Select Input (CSI, PD2) can be used
to disable the internal memories, placing them
in Stand-by mode even if inputs are changing.
This feature does not block any internal signals
or disable the PLDs. This is a good alternative
to using the APD Unit, especially if your MCU
has a chip select output. There is a slight
penalty in memory access time when PSD Chip
Select Input (CSI, PD2) makes its initial
transition from deselected to selected.
I
The Power Management Mode Registers
(PMMR) can be written by the MCU at run-time
to manage power. All PSD devices support
“blocking bits” in these registers that are set to
block designated signals from reaching both
PLDs. Current consumption of the PLDs is
directly related to the composite frequency of
the changes on their inputs (see Figure 35).
Significant power savings can be achieved by
blocking signals that are not used in DPLD or
CPLD logic equations at run-time. PSDsoft Ex-
press creates a fuse map that automatically
blocks the low address byte (A7-A0) or the con-
trol signals (CNTL0-CNTL2, ALE and Write En-
able High-byte (WRH/DBE, PD3)) if none of
these signals are used in PLD logic equations.
PSD devices have a Turbo bit in PMMR0. This
bit can be set to turn the Turbo mode off (the de-
fault is with Turbo mode turned on). While Turbo
mode is off, the PLDs can achieve Stand-by cur-
rent when no PLD inputs are changing (zero DC
current). Even when inputs do change, signifi-
cant power can be saved at lower frequencies
(AC current), compared to when Turbo mode is
on. When the Turbo mode is on, there is a sig-
nificant DC current component, and the AC
component is higher.
相關PDF資料 |
PDF描述 |
|---|---|
| PSD4235G2-B-70M | Flash In-System Programmable ISP Peripherals For 16-bit MCUs 5V Supply |
| PSD4235G2-B-70MI | CAP 0.47UF 25V 20% TANT SMD-3216-18 TR-7-PL GOLD |
| PSD4235G2-B-70U | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4235G2-B-70UI | CAP 0.47UF 25V 20% TANT SMD-3216-18 TR-7-PL SN100% |
| PSD4235G2-C-70U | Flash In-System Programmable ISP Peripherals For 16-bit MCUs 5V Supply |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD4235G2V-12UI | 功能描述:CPLD - 復雜可編程邏輯器件 3.3V 4M 120ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| PSD4235G2V-90U | 功能描述:CPLD - 復雜可編程邏輯器件 3.3V 4M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| PSD4256G6V-10UI | 功能描述:CPLD - 復雜可編程邏輯器件 3.3V 8M 100ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| PSD4-36 | 制造商:Tamura Corporation of America 功能描述: |
| PSD-45 | 制造商:MEANWELL 制造商全稱:Mean Well Enterprises Co., Ltd. 功能描述:45W DC-DC Single Output Switching Power Supply |
發布緊急采購，3分鐘左右您將得到回復。