- 您現在的位置：買賣IC網 > PDF目錄368343 > PT6222C 20V Single N-Channel HEXFET Power MOSFET in a SO-8 package; Similar to IRF7460 with Lead Free Packaging PDF資料下載
參數資料
| 型號： | PT6222C |
| 英文描述： | 20V Single N-Channel HEXFET Power MOSFET in a SO-8 package; Similar to IRF7460 with Lead Free Packaging |
| 中文描述： | 模擬IC |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 511K |
| 代理商： | PT6222C |
For assistance or to order, call
(800) 531-5782
5
Power Trends, Inc.
27715 Diehl Road, Warrenville, IL 60555
(800) 531-5782
Fax: (630) 393-6902
http://www.powertrends.com
A p p l i c a t i o n
N o t e s
PT6100/6120/6210/6220/6300/6320 Series
More Application Notes
Using the Inhibit Function on Power Trends’
Wide Input Range Bus ISRs
For applications requiring output voltage On/Off control, the
12pin ISR products incorporate an inhibit function. The func-
tion has uses in areas such as battery conservation, power-up
sequencing, or any other application where the regulated output
from the module is required to be switched off. The On/Off
function is provided by the
Inhibit
control, pin 1.
The ISR functions normally with pin 1 open-circuit, providing a
regulated output whenever a valid source voltage is applied to
V
in
, (pins 2, 3, & 4). When a low-level
2
ground signal is applied
to pin 1 the regulator output is disabled, and the input current to
the ISR is reduced to about 100
μ
A
3/
.
Figure 1 shows an application schematic, which details the typi-
cal use of the inhibit function. Note the discrete transistor, Q1.
The inhibit control has its own internal pull-up with a maximum
open-circuit voltage of 8.3VDC. Only devices with a true open-
collector or open-drain output can be used to control this pin. A
discrete bipolar transistor or MOSFET is recommended.
Notes:
1. The inhibit control logic is similar for all Power Trends’
modules, but the flexibility and threshold tolerances will be
different. For specific information on the inhibit function of
other ISR models, consult the applicable application note.
2. Use only a true open-collector device (preferably a discrete
transistor) for the inhibit input. Do Not use a pull-up resis-
tor, or drive the input directly from the output of a TTL or
other logic gate. To disable the output voltage, the control
pin should be pulled low to less than +1.5VDC.
3. The following equation may be used to determine the ap-
proximate current drawn from the input supply at V
in
, and
through Q1 when the inhibit is active.
I
stby
= V
in
÷
155k
± 20%
4. When the inhibit control pin is active, i.e. pulled low, the
maximum input voltage is limited to +30Vdc.
5. Do not control the inhibit input with an external DC volt-
age. This will lead to erratic operation of the ISR and may
over-stress the regulator.
6. Avoid capacitance greater than 500pF at the Inhibit control
pin. Excessive capacitance at this pin will cause the ISR to
produce a pulse on the output voltage bus at turn-on.
7. Keep the On/Off transition to less than 10
μ
s. This prevents
erratic operation of the ISR, which can cause a momentary
high output voltage.
C2
100
μ
F
+
C1, 1
μ
F
(Optional)
V
out
COM
V
in
COM
Inh
Q1
2N7002
PT6100/6210/6300
9,10,11
12
5,6,7,8
2,3,4
Vin
Vo
GND
Vo(adj)
1
Inh
Figure 1
Turn-On Time:
The output of the ISR is enabled automatically
when external power is applied to the input. The
Inhibit
control
pin is pulled high by its internal pull-up resistor. The ISR pro-
duces a fully regulated output voltage within 1-msec of either the
release of the Inhibit control pin, or the application of power.
The actual turn-on time will vary with the input voltage, output
load, and the total amount of capacitance connected to the out-
put Using the circuit of Figure 1, Figure 2 shows the typical rise
in output voltage for the PT6101 following the turn-off of Q1 at
time t =0. The waveform was measured with a 9Vdc input volt-
age, and 5-Ohm resistive load.
Figure 2
0
1
2
3
4
5
6
-0.2
0
0.2
0.4
0.6
0.8
1
t (milli-secs)
V
o
相關PDF資料 |
PDF描述 |
|---|---|
| PT6222N | Analog IC |
| PT6223 | 3.3V 2A Wide-Input Low Drop-Out Adjustable Step-Down ISR |
| PT6223A | 40V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; A IRL1004 with Standard Packaging |
| PT6223C | 55V Single N-Channel HEXFET Power MOSFET in a I-Pak package; A IRLU2705 with Standard Packaging |
| PT6223N | A 30V Single N-Channel HEXFET Power MOSFET in a DirectFET ST package rated at 72 amperes optimized with low on resistance for applications such as active OR'ing. Shipped in Tape and Reel only. Part is not available in bulk, TR is implied in part number.; A IRF6626 with Standard Tape and Reel Quantity of 4800 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT6222G | 功能描述:REGULATOR 5V 2A HORZ HZ HT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT6220 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最?。?36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
| PT6222H | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2 AMP ADJUSTABLE LOW VOLTAGE INPUT INTEGRATED SWITCHING REGULATOR |
| PT6222J | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2 AMP ADJUSTABLE LOW VOLTAGE INPUT INTEGRATED SWITCHING REGULATOR |
| PT6222N | 功能描述:開關變換器、穩壓器與控制器 5V 2A Wide-Inp LDO Adj Step-Down ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| PT6222R | 功能描述:REGULATOR 5V 2A VERT HZ HT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT6220 標準包裝:10 系列:PT4570 類型:隔離 輸出數:1 電壓 - 輸入（最小）:36V 電壓 - 輸入（最大）:75V Voltage - Output 1:9V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:3.3A 電源（瓦） - 制造商系列:30W 電壓 - 隔離:1.5kV（1500V） 特點:- 安裝類型:表面貼裝 封裝/外殼:19-SIP SMD 模塊 尺寸/尺寸:3.00" L x 1.19" W x 0.50" H（76.2mm x 30.2mm x 12.7mm） 包裝:托盤 工作溫度:-40°C ~ 85°C 效率:84% 電源（瓦特）- 最大:30W |
發布緊急采購，3分鐘左右您將得到回復。