- 您現在的位置：買賣IC網 > PDF目錄368345 > PT6474 1.8V 14A. 3.3-V Input Adjustable Step-Down ISR PDF資料下載
參數資料
| 型號： | PT6474 |
| 英文描述： | 1.8V 14A. 3.3-V Input Adjustable Step-Down ISR |
| 中文描述： | 1.8V的第14A條。 3.3 - V輸入可調降壓ISR的 |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 181K |
| 代理商： | PT6474 |
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com
PT6460 & PT6470 Series
Output Remote Sense
The
(+)Sense
pin allows the regulator to compensate for
limited amounts of ‘IR’ voltage drop in the positive output
connection resistance. This is the voltage drop incurred
in the PCB trace between
Vout
(pins 9 & 10) of the regu-
lator and the load some distance away. Connecting
(+)Sense
to the positive load terminal improves the voltage regu-
lation at the load, particularly when the load current
fluctuates. Although not recommended, leaving
(+)Sense
disconnected will not damage the regulator or the load
circuitry. An internal 10
resistor, connected between
the sense pin and the output, keeps the output voltage in
regulation.
With the sense pin connected, the difference between
the voltage measured between
V
out
and
GND
at the
regulator, and that measured from
(+)Sense
to
GND
, is
the amount of IR drop being compensated by the regula-
tor. This should be limited to 0.3 V maximum.
Note: The remote sense feature is not designed to compensate
for the forward drop of non-linear or frequency dependent
components that may be placed in series with the converter
output. Examples include OR-ing diodes, filter inductors,
ferrite beads, and fuses. When these components are enclosed
by the remote sense connections they are effectively placed
inside the regulation control loop, which can adversely affect
the stability of the regulator.
Pre-Bias Startup
In complex digital systems an external voltage can some-
times be present at the output of the regulator during
power up. For example, this voltage may be backfed
through a dual-supply logic component such as an FPGA
or ASIC. Another path might be via a clamp diode (to a
lower supply voltage) as part of a power-up sequencing
implementation.
Although the PT6460 (5-V input) and PT6470 (3.3-V
input) series of regulators will sink current under steady-
state conditions, they will not do so during startup. This
feature allows these regulators to start up while an external
voltage is simultaneously applied to the output. To facilitate
this feature the input voltage must always be greater than
or equal to the output voltage throughout the power-up
and power-down sequence. Startup includes both the
application of a valid input source voltage, or the removal
of a ground signal from the
Inhibit*
control (pin 1) with
a valid input source applied. The output of the regulator
is also effectively off (tri-state), during the period that
the
Inhibit*
control is held low.
Note: If the pre-bias is greater than the nominal regulation
voltage, the module will begin sinking current at the end of its
soft-start power-up sequence. This could overstress the regulator if
the current exceeds its rated output.
Over-Current Protection
To protect against load faults, these ISRs incorporate
output over-current protection. Applying a load that
exceeds the over-current threshold (see data sheet speci-
fications) will cause the regulated output to shut down.
Following shutdown the ISR will periodically attempt to
recover by initiating a soft-start power-up. This is often
described as a “hiccup” mode of operation, whereby the
module continues in a cycle of successive shutdown and
power up until the load fault is removed. During this
period, the average current flowing into the fault is
significantly reduced. Once the fault is removed, the
converter automatically recovers and returns to normal
operation.
Operating Features and System Considerations
for the PT6460 & PT6470 Regulator Series
The PT6460 (5-V input) and the PT6470 (3.3-V input)
series of integrated switching regulators (ISRs) provide
step-down voltage conversion for output loads of up to
14 A.
Power up & Soft-Start Timing
Following either the application of a valid input source
voltage, or the removal of a ground signal to the
Inhihit*
control pin (with input power applied), the regulator will
initiate a soft-start power up. A soft start slows the rate at
which the output voltage rises and introduces a short time
delay, t
d
(approximately 2 ms), into the power-up sequence.
Figure 1-1 shows the power-up characteristic of a PT6464
(5-V input, 1.8-V output) with a 8.5-A load.
Vo (1V/Div)
Iin (2A/Div)
Vin (2V/Div)
HORIZ SCALE: 5ms/Div
t
d
Figure 1-1
相關PDF資料 |
PDF描述 |
|---|---|
| PT6475 | 1.5V 14A. 3.3-V Input Adjustable Step-Down ISR |
| PT6476 | 60V Single N-Channel HEXFET Power MOSFET in a SO-8 package; A IRF7478 with Standard Packaging |
| PT6477 | 200V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; Similar to IRFB31N20D with Lead Free Packaging |
| PT65-103 | 55V Single N-Channel HEXFET Power MOSFET in a TO-220AB package; Similar to the IRFZ24N in lead free packaging |
| PT65-103-L508 | 30V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRLR7821 with Standard Packaging |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT6474A | 功能描述:REG 1.8V 14A 3.3VIN ADJ HORZ RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT6470 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?55V 電壓 - 輸入（最大）:100V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:200W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| PT6474C | 功能描述:REG 1.8V 14A 3.3VIN ADJ SMD RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT6470 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?55V 電壓 - 輸入（最大）:100V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:200W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| PT6474N | 功能描述:開關變換器、穩壓器與控制器 1.8V 14A 3.3-V Inpt Adj Step-Down ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| PT6475 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.5V 14A. 3.3-V Input Adjustable Step-Down ISR |
| PT6475A | 功能描述:開關變換器、穩壓器與控制器 1.5V 14A 3.3-V Inpt Adj Step-Down ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。