參數資料
型號: PT7673
英文描述: Half Bridge Driver, LO In Phase with RT, Programmable Oscillating Frequency, 0.6us Deadtime in a 8-pin DIP package and differenct phase; Similar to IR21531D with Lead Free Packaging
中文描述: 0.8V至1.575V 30A條。 5 - V輸入可編程ISR的
文件頁數: 7/9頁
文件大小: 184K
代理商: PT7673
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com
PT7670 Series
Using the Standby Function on the PT7670
Series of 30-A Switching Regulators
For applications requiring On/Off control of the output
voltage, the 30-A rated PT7670 series of Excalibur ISRs
incorporate an on/off “Standby” function. This feature
may be used for power-up/shutdown sequencing, or to
change the output voltage while input power is applied.
See related notes:
“Pin-Coded Output Voltage Adjustment
of the PT7670 Series of 30-A ISRs.”
The standby function is provided by the
STBY*
control,
pin 5. If pin 5 is left open-circuit the regulator operates
normally, providing a regulated output whenever a valid
supply voltage is applied to V
in
(pins 7-11) with respect to
GND (pins 13-19). Connecting pin 5 to ground
1
will
disable the regulator output
2
. This places the regulator
in standby mode, and reduces the input current to typically
6mA. If a ground signal is applied to pin 5 prior to power-
up, the regulator output will remain inactive during the
period that input power is applied.
The standby input must be controlled with an open-
collector (or open-drain) discrete transistor (See Figure
3-1). Table 3-1 gives the input requirements.
Table 3-1 Standby Control Input Requirements
Parameter
Min
Enable
2 V
Disable
–0.2 V
I
stby (low)
Vstby (o/c)
Typ
Max
Open Cct.
1
0.8 V
0.5 mA
V
in
Notes:
1. The Standby input of the PT7670 series of regulators
should be controlled using an open-collector (or open-
drain) discrete transistor.
Do Not
use a pull-up resistor. The
control input has an open-circuit voltage equal to V
in
. To
set the regulator output to zero, the control pin must be
“pulled” to less than 0.8Vdc with a 0.5mA sink to ground.
Figure 3-1
Turn-On Time:
Turning Q
1
in Fig. 3-1 off, removes the
low-voltage signal at pin 5 and enables the output
3
. Af-
ter a delay of less than 5 ms, the output voltage rises to
full regulation within 30 ms
4
. Fig. 3-2 shows the typical
output voltage waveform of a PT7671 following the
turn-off of Q
1
at time t =0 secs. In the circuit of Fig. 3-1,
the output voltage is set to 3.3 V. The waveform was
measured with a +5-V input source voltage, and 15-A
output load.
Figure 3-2
C
out
+
C
in
+
5 V
COM
Inhibit
L
O
A
D
PT7671
4
3
1
26
20
25
12
5
13
19
7
11
Vo
Vin
GND
Senes(+)
STBY
VID3 - VID0
Senes(
)
V
o
=3.3 V
COM
Q
BSS138
2
Iin (5A/Div)
Vo (2V/Div)
Vstby (5V/Div)
HORIZ SCALE: 5ms/Div
2. In the standby mode the output of the regulator is tri-
state, and the output voltage falls at the rate that the
load circuit discharges the output filter capacitors.
3. When the ground signal to the
Standby
pin is removed,
the regulator output initiates a soft-start cycle by first
asserting a low impedance to ground. If an external
voltage is applied to the output bus, it will sink current and
possibly over-stress the part.
4. The turn-off time of Q
1
, or rise time of the standby input
is not critical. Turning Q
1
off slowly will not affect regulator
operation. However, a slow turn-off time will increase
both the initial delay and rise-time of the output voltage.
相關PDF資料
PDF描述
PT7675 Ballast Control, Below Resonance Protection, Thermal Overload Protection, Protection from Failure to Strike, Programmable Preheat Time and Run Frequency, Programmable Deadtime, Automatic Restart for Lamp Exchange in a 16-pin DIP package; A IR21571 with Standard Packaging
PT7712 600V Half Bridge Driver LED Buck Regulator in a 8-Pin SOIC Package; A IRS2541 packaged in a Lead-Free 8-Lead SOIC shipped on Tape and Reel
PT7713 200V Half Bridge Driver LED Buck Regulator in a 8-Lead Dip Package; A IRS2540 packaged in a Lead-Free 8-Lead DIP
PT7714 200V Half Bridge Driver LED Buck Regulator in a 8-Pin SOIC Package; A IRS2540 packaged in a Lead-Free 8-Lead SOIC shipped on Tape and Reel
PT7715 Single High Side Driver, Noninverting Input. IN Voltage Threshold 9.5V & 6.0V; A IRS2118 packaged in a Lead-Free 8-Lead SOIC
相關代理商/技術參數
參數描述
PT7673A 功能描述:REG PROG .8-1.575V 30A 5VIN HORZ RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT7670 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入(最?。?55V 電壓 - 輸入(最大):100V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出(最大):* 電源(瓦) - 制造商系列:200W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H(116.8mm x 47.2mm x 20.1mm) 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源(瓦特)- 最大:*
PT7673C 功能描述:REG PROG .8-1.575V 30A 5VIN SMD RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT7670 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入(最?。?55V 電壓 - 輸入(最大):100V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出(最大):* 電源(瓦) - 制造商系列:200W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H(116.8mm x 47.2mm x 20.1mm) 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源(瓦特)- 最大:*
PT7673N 功能描述:開關變換器、穩壓器與控制器 0.8V to 1.575V 30A 5-V Input Prog ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
PT7675 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.075V to 1.85V 30A. 5-V Input Programmable ISR
PT7675A 功能描述:開關變換器、穩壓器與控制器 PROGRAMMABLE ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel