- 您現在的位置：買賣IC網 > PDF目錄378085 > PT8101C (Texas Instruments, Inc.) Isolated Flyback Switching Regulator with 9V Output PDF資料下載
參數資料
| 型號： | PT8101C |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Isolated Flyback Switching Regulator with 9V Output |
| 中文描述： | 隔離反激式開關穩壓9V輸出 |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 231K |
| 代理商： | PT8101C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com
10
Pin-Coded Output Voltage Programming of the
40-A Rated PT8100 Series Regulators
The PT8100 series of Excalibur ISRs incorporate a
pin-coded programmable output voltage. In each case
the desired output voltage must be selected from a preset
range defined by the regulator model. Programming is
achieved by selectively connecting the control inputs,
“VID0–VID4”
(
“VID 25mV–VID3”
for PT8104), pins 1–5,
to the
“VID Common,”
pin 11.
1
The programming code
and pinout information for each model is provided in the
PT8100 specifications. Some of the program codes are
compatible with the “Voltage ID” codes defined by the
Intel VRM specifications. Figure 1 shows the pin-strap
connections for selecting 1.5V output voltage from a
PT8101.
Notes:
1. The programming convention is as follows:-
Logic 0:
Connect to pin 11 (VID Common).
Logic 1:
Open circuit/open drain (See notes 2, & 4)
2. The output voltage range of the PT8101 is limited to
2.7V maximum. Above this voltage, the performance of
the module is not guaranteed. Although the module will
appear to function above this voltage, VID 4 (pin 5)
should not be used to set the output voltage higher than
2.7V.
3. Do not connect pull-up resistors to the voltage
programming pins.
4. To minimize output voltage error, use pin 11 (VID
Common) as the logic “0” reference. However if the
regulator is used to power a VRM compatible
Figure 1
microprocessor this may not be possible. In this case
either connect pin 11 to pins 17–22, or the ground
plane close to the regulator. This will allow the
microprocessor to use the common ground as a VID
control reference.
4. If active devices are used to ground the voltage control
pins, low-level open-drain MOSFETs should be used over
bipolar transistors. The inherent V
ce
(sat) in bipolar devices
introduces errors in the device’s internal voltage control
circuit. Discrete transistors such as the BSS138, 2N7002,
IRLML2402, are examples of appropriate devices.
Active Voltage Programming:
Special precautions should be taken when making changes
to the voltage control progam code while the output is
active. It is recommended that the ISR be powered down
or placed in standby. Changes made to the program code
while V
out
is active can induce high current transients
through the device. This is the result of the electrolytic
output capacitors being either charged or discharged to the
new output voltage set-point. The transient current can be
minimized by making only incremental changes to the
binary code, i.e. one LSB at a time. A minimum of 100μs
settling time between each program state is also recom-
mended. Making non-incremental changes to VID3 and
VID4 with the output enabled is discouraged. The tran-
sients induced may activate the module’s over-current
protection. When using active devices to program the
output voltage, their state should be asserted prior to
input power being applied. If this is not possible, pull
STBY*
(pin 6) to GND during the application of power,
assert the program code, then release pin 6. The release
of pin 6 will then to allow the device to initiate a soft-
start power-up to the program voltage.
PT8100 Series
L
O
A
D
C
OUT
+
C
IN
+
V
IN
V
O
=1.5V
GND
V
O
SENSE
L
in
1μH
GND
VID0
VID1
VID2
VID3
VID4
PT8101
4
3
2
1
31
23
–
30
6
17
–
22
12
–
16
5
11
VID4
–
VID0
Sense
V
IN
V
OUT
STBY
GND
VID
Common
Q1
BSS138
1 =OFF
相關PDF資料 |
PDF描述 |
|---|---|
| PT8102A | Isolated Flyback Switching Regulator with 9V Output |
| PT8103N | Isolated Flyback Switching Regulator with 9V Output |
| PT8104N | Isolated Flyback Switching Regulator with 9V Output |
| PT8105A | FILTER CABLE/CLAMP 35 OHM 7MM |
| PTB20003 | 4 Watts, 915-960 MHz Cellular Radio RF Power Transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT8101N | 功能描述:REG 1.3-2.7V 40A 5VIN PROG VERT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:PT8100 設計資源:Maxi/Mini/Micro Design Guide, Appl Manual 標準包裝:1 系列:Maxi 類型:隔離 輸出數:1 電壓 - 輸入（最?。?43V 電壓 - 輸入（最大）:110V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:400W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:模塊 尺寸/尺寸:4.60" L x 2.20" W x 0.54" H（116.8mm x 55.9mm x 13.7mm） 包裝:散裝 工作溫度:-55°C ~ 100°C 效率:* 電源（瓦特）- 最大:* |
| PT8102 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:40-A 3.3/5-V Input Programmable Integrated Switching Regulator |
| PT8102A | 功能描述:開關變換器、穩壓器與控制器 PROGRAMMABLE ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| PT8102C | 制造商:TI 制造商全稱:Texas Instruments 功能描述:40-A 3.3/5-V Input Programmable Integrated Switching Regulator |
| PT8102N | 功能描述:DC/DC轉換器 PROGRAMMABLE ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。