- 您現在的位置：買賣IC網 > PDF目錄69251 > PT8A2611P (PERICOM SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDIP16 PDF資料下載
參數資料
| 型號： | PT8A2611P |
| 廠商： | PERICOM SEMICONDUCTOR CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 206K |
| 代理商： | PT8A2611P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁
Data Sheet
PT8A2611/2621
PIR Sensor Light Switch Controller
PT0091(11/03)
Ver:3
7
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Power On Initial
The PIR signal amplifier requires a warm up period after power-
on. The input should be disabled during this period.
In the AUTO mode within the first 40 seconds of the initial
time the chip allows override control to enter the quickly in-
stall mode, After 40s of the initial time the chip allows over-
ride control between ON and AUTO. It will remain in the warm
up period if the total initial time has not elapsed after return-
ing to AUTO.
In case that the ZC signal disappears more than 3 seconds, the
chip will restart the initialization operation. However, the re-
start initial time is always 40 seconds and cannot be extended
by adding C
RST to the RST pin as shown in Figure 4.
Trigger
The trigger timing is shown in Figure 7.
Retrigger -- If another signal is attained in trigger hold time,
the circuit will be retriggered, and the trigger hold time will be
started from this time.
Figure 7. Trigger Timing
Comparator
Input
+trigger level
-trigger level
CDS
Output
Enable
5s
RELAY
TRIAC
Test
Enable
Detect
Enable
10s test
enable
ON
(Note2)
pulse out
power on delay time
40s
RST
Comparator
Output
>24ms
<24ms
(Note1)
Notes:
1. The output is activated if the trigger signal conforms to the following criteria:
- More than 3 triggers within 2 seconds,
- A trigger signal sustain duration > 0.34 seconds, and
- 2 triggers within 2 seconds with pulse duration of one > 0.16 seconds.
-The effective comparator output width is 24ms.(Fosc=16KHz)
2. The output duration is set by an external RC connected to the OSCD pin.
相關PDF資料 |
PDF描述 |
|---|---|
| PT8A2611W | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| PT8A2621W | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| PT8A2621DE | SPECIALTY ANALOG CIRCUIT, UUC18 |
| PT8A2611DE | SPECIALTY ANALOG CIRCUIT, UUC18 |
| PT8A262P | SPECIALTY ANALOG CIRCUIT, PDIP16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT8A2611W | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:PIR Sensor Light Switch Controller |
| PT8A2612 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:PIR Sensor Light Switch Controller |
| PT8A2612DE | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:PIR Sensor Light Switch Controller |
| PT8A2612P | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:PIR Sensor Light Switch Controller |
| PT8A2612W | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:PIR Sensor Light Switch Controller |
發布緊急采購，3分鐘左右您將得到回復。