- 您現在的位置：買賣IC網 > PDF目錄69251 > PTB48520WAS (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTB48520WAS |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-10 |
| 文件頁數： | 16/18頁 |
| 文件大小： | 427K |
| 代理商： | PTB48520WAS |
www.ti.com
Overtemperature Protection
Undervoltage Lockout
Primary-Secondary Isolation
Output Voltage Adjustment
Rset + 6.49 kW
1.225 V
Vset * 1.805 V
* 4.42 kW
(1)
PTB48520W
SLTS233A–NOVEMBER 2004–REVISED APRIL 2005
APPLICATION INFORMATION (continued)
higher. Depending on the load conditions on the VO Seq output, the voltage at VO Bus maybeupto100 mV
higher than the converter set-point voltage. In addition, the Smart-Sense feature (incorporated into the converter)
only engages sense compensation to the VO Seq output when that output voltage is close to the set point. During
other conditions, such as power-up and power-down sequencing events, the sense circuit automatically defaults
to sensing the VO Bus voltage, internal to the converter.
Leaving the (+)Sense and (–)Sense pins open does not damage the converter or load circuitry. The converter
includes default circuitry that keeps the output voltage in regulation. If the remote sense feature is not used, the
(–)Sense pin should always be connected to VO COM.
Note: The remote sense feature is not designed to compensate for the forward drop of nonlinear or frequency
dependent components that may be placed in series with the converter output. Examples include OR-ing diodes,
filter inductors, ferrite beads, and fuses. When these components are enclosed by the sense pin connections,
they are effectively placed inside the regulation control loop, which can adversely affect the stability of the
converter.
Overtemperature protection is provided by an internal temperature sensor, which monitors the temperature of the
converter PCB (close to pin 1). If the PCB temperature exceeds a nominal 115°C, the converter shuts down. The
converter then automatically restarts when the sensed temperature falls to approximately 105°C. When operated
outside its recommended thermal derating envelope (see data sheet derating curves), the converter typcially
cycles on and off at intervals from a few seconds to one or two minutes. This is to ensure that the internal
components are not permanently damaged from excessive thermal stress.
The undervoltage lockout (UVLO) is designed to prevent the operation of the converter until the input voltage is
close to the minimum operating voltage. The converter is held off when the input voltage is below the UVLO
threshold, and turns on when the input voltage rises above the threshold. This prevents high start-up current
during normal power up of the converter, and minimizes the current drain from the input source during low input
voltage conditions. The converter meets full specifications when the minimum specified input voltage is reached.
The UVLO circuitry also overrides the operation of the VO Enable control. Only when the input voltage is above
the UVLO threshold is the VO Enable control functional.
These converters incorporate electrical isolation between the input terminals (primary) and the output terminals
(secondary). All converters are tested to a withstand voltage of 1500 VDC. This complies with UL/cUL 60950 and
EN 60950 and the requirements for operational isolation. It allows the converter to be configured for either a
positive or negative input voltage source. The data sheet Terminal Functions table provides guidance as to the
correct reference that must be used for the external control signals.
The VO Adjust control sets the output voltages to a value higher than 1.8 V. For output voltages other than 1.8 V
a single external resistor, R(set), must be connected directly between VO Adjust (pin 7) and (–)Sense (pin 6) pins.
A 0.05-W rated resistor can be used. The tolerance should be 1%, with a temperature stability of 100 ppm/°C (or
better). Place the resistor close to the converter and connect it directly between pins 7 and 6 using dedicated
PCB traces (see typical application). Table 1 gives the preferred value of the external resistor for a number of
standard voltages, along with the actual output voltage that this resistance value provides.
For other output voltages the value of the required adjust resistor may be calculated using Equation 1.
7
相關PDF資料 |
PDF描述 |
|---|---|
| PTB48520WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTB48560AAS | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| PTB48560CAH | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| PTB48560CAZ | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| PTB48560AAH | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTB48520WAZ | 功能描述:DC/DC轉換器 25A 48V Input Iso DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTB48530AAH | 功能描述:PTB48530AAH RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:- 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?55V 電壓 - 輸入（最大）:100V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:200W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| PTB48530AAS | 功能描述:PTB48530AAS RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:- 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?55V 電壓 - 輸入（最大）:100V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:200W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| PTB48530AAZ | 功能描述:CONV DC-DC 48V 27W DUAL 7-SMD RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:PTB48530A 標準包裝:500 系列:Econoline R0.25S 類型:隔離 輸出數:1 電壓 - 輸入（最小）:21.6V 電壓 - 輸入（最大）:26.4V Voltage - Output 1:3.3V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:76mA 電源（瓦） - 制造商系列:0.25W，1/4W 電壓 - 隔離:1kV（1000V） 特點:- 安裝類型:表面貼裝 封裝/外殼:8-DIP SMD 模塊 尺寸/尺寸:0.49" L x 0.42" W x 0.28" H（12.8mm x 10.7mm x 7.0mm） 包裝:帶卷 (TR) 工作溫度:-40°C ~ 100°C 效率:60 ~ 70% 電源（瓦特）- 最大:0.25W |
| PTB48530BAS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。