- 您現在的位置：買賣IC網 > PDF目錄98063 > PTB78560CAS (TEXAS INSTRUMENTS INC) 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTB78560CAS |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-11 |
| 文件頁數： | 5/27頁 |
| 文件大小： | 643K |
| 代理商： | PTB78560CAS |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
www.ti.com
Input Overvoltage Protection
Differential Output Voltage Sense
Overtemperature Protection
Output Voltage Adjustment
SLTS249 – JUNE 2005
APPLICATION INFORMATION (continued)
output that exceeds the converter overcurrent threshold (see applicable specification) causes the output voltage
to momentarily fold back, and then shut down. Following shutdown, the module periodically attempts to
automatically recover by initiating a soft-start power up. This is often described as a hiccup mode of operation,
whereby the module continues in the cycle of successive shutdown and power up until the load fault is removed.
Once the fault is removed, the converter automatically recovers and returns to normal operation.
The converter protects itself against input voltage surges and transients of up to 100 V. This is above the
maximum continuous operating input voltage of 60 V. In order to protect itself, the converter output is disabled at
some voltage above 60 V. This is to ensure that the converter internal components are not exposed to voltages
above their stress ratings. The converter output remains off for some of the period that the input voltage is
above the maximum continuous rating. Once the overvoltage event has passed, the output from the converter
automatically restarts by executing a soft-start power up.
A differential remote sense allows a converter regulation circuitry to compensate for limited amounts of IR drop,
that may be incurred between the converter and load, in either the positive or return PCB traces. Connecting the
+Sense and –Sense pins to the respective positive and ground reference of the load terminals improves the load
regulation of the converter output voltage at that connection point. The –Sense pin should always be connected
to the VO COM. The +Sense pin may be connected to either the +VO Bus or +VO Seq outputs.
When the +Sense pin is connected to the VO Seq output, the voltage at VO Bus voltage regulates slightly higher.
Depending on the load conditions on the VO Seq output, the voltage at VO Bus may be up to 100 mV higher than
the converter set-point voltage. In addition, the Smart-Sense feature (incorporated into the converter) only
engages sense compensation to the VO Seq output when that output voltage is close to the set-point. During a
power-up sequencing event, the sense circuit automatically defaults to sensing the VO Bus voltage, internal to
the converter.
Leaving the +Sense and –Sense pins open does not damage the converter or load circuit. The converter
includes default circuitry that keeps the output voltage in regulation. However, if the remote sense feature is not
used, the –Sense pin should still be connected to VOCOM.
Note: The remote sense feature is not designed to compensate for the forward drop of nonlinear or
frequency-dependent components that may be placed in series with the converter output. Examples include
OR-ing diodes, filter inductors, ferrite beads, and fuses. When these components are enclosed by the sense pin
connections, they are effectively placed inside the regulation control loop, which can adversely affect the stability
of the converter.
Overtemperature protection is provided by an internal temperature sensor, which monitors the temperature of
the converter PCB (close to pin 1). If the PCB temperature exceeds a nominal 115°C, the converter shuts down.
The converter then automatically restarts when the sensed temperature falls to approximately 105°C. When
operated outside its recommended thermal derating envelope (see data sheet derating curves), the converter
typcially cycles on and off at intervals from a few seconds to one or two minutes. This is to ensure that the
internal components are not permanently damaged from excessive thermal stress.
An external resistor is required to set the nominal output voltage(s) of the converter to a voltage higher than its
minimum value. The resistor, RSET, must be connected directly between the VO Adjust (pin 8) and –Sense (pin
7) terminals. A 0.05-W rated resistor can be used. The tolerance should be 1%, with a temperature stability of
100 ppm/°C (or better). Place the resistor close to the converter and connect it using dedicated PCB traces (see
Figure 22). Table 1 gives the nearest standard value of external resistor for the common voltages within each
model's adjust range. The actual output voltage that the resistor value provides is also provided.
13
相關PDF資料 |
PDF描述 |
|---|---|
| PTB78560BAZ | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| PTB78560BAH | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| PTB78560CAZ | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| PTB78560AAZ | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| PTB78560AAS | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTB78560CAZ | 功能描述:DC/DC轉換器 30-W 24-V/48V Input DC/DC Converter RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTB8 | 功能描述:烙鐵 Weller Scrwdrvr Tip For TC201 .093"x800 RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| PT-B8 | 制造商:Cooper Tools / Weller 功能描述:Bulk 制造商:Cooper Hand Tools / Weller 功能描述:TIP SCREWDRIVER 2.4MM 制造商:WELLER 功能描述:TIP, SCREWDRIVER, 2.4MM |
| PTB82PS | 制造商:Amphenol Aerospace 功能描述:Conn MIL-C-26482 Circular PIN/SKT 2 POS Solder ST Panel Mount 2 Terminal 1 Port 制造商:Amphenol Aerospace 功能描述:Conn Miniature Cylindrical PIN/SKT 2 POS Solder ST Panel Mount 2 Terminal 1 Port |
| PTB-8-2PS | 制造商:Amphenol Corporation 功能描述:connector,thru bulkhead receptacle,size 8,2#20 pin to 2#20 socket contact 制造商:Amphenol Corporation 功能描述:CONN 26482 CIRC PIN/SKT 2 POS SLDR ST PNL MNT 2TERM - Bulk |
發布緊急采購，3分鐘左右您將得到回復。