參數資料
型號: PTH03010WAST
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源模塊
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封裝: DIP-10
文件頁數: 12/19頁
文件大小: 510K
代理商: PTH03010WAST
For technical support and more information, visit http://power.ti.com
Pin Descriptions
Vin:
The positive input voltage power node to the mod-
ule, which is referenced to common GND.
Vout:
The regulated positive power output with respect
to the GND node.
GND:
This is the common ground connection for the
Vin and Vout power connections. It is also the 0 VDC
reference for the control inputs.
Inhibit:
The Inhibit pin is an open-collector/drain negative
logic input that is referenced to GND. Applying a low-
level ground signal to this input disables the module’s
output and turns off the output voltage. When the Inhibit
control is active, the input current drawn by the regula-
tor is significantly reduced. If the Inhibit pin is left
open-circuit, the module will produce an output when-
ever a valid input source is applied.
Vo Adjust:
A 0.1 W 1 % resistor must be directly connected
between this pin and pin 7 (GND) to set the output voltage
to a value higher than 0.8 V. The temperature stability of
the resistor should be 100 ppm/°C (or better). The set
point range for the output voltage is from 0.8 V to 2.5 V.
The resistor value required for a given output voltage
may be calculated from the following formula. If left
open circuit, the output voltage will default to its lowest
value. For further information on output voltage adjust-
ment, consult the related application note.
Rset
= 10 k
0.8 V
– 2.49 k
Vout – 0.8 V
The specification table gives the preferred resistor values
for a number of standard output voltages.
Vo Sense:
The sense input allows the regulation circuit to
compensate for voltage drop between the module and
the load. For optimal voltage accuracy Vo Sense should be
connected to Vout. It can also be left disconnected.
Track:
This is an analog control input that enables the
output voltage to follow an external voltage. This pin
becomes active typically 20 ms after the input voltage
has been applied, and allows direct control of the output
voltage from 0 V up to the nominal set-point voltage.
Within this range the output will follow the voltage at
the Track pin on a volt-for-volt basis. When the control
voltage is raised above this range, the module regulates
at its set-point voltage. The feature allows the output
voltage to rise simultaneously with other modules pow-
ered from the same input bus. If unused, this input should
be connected to Vin. Note: Due to the under-voltage lockout
feature, the output of the module cannot follow its own input
voltage during power up. For more information, consult the
related application note.
Margin Down:
When this input is asserted to GND, the
output voltage is decreased by 5% from the nominal. The
input requires an open-collector (open-drain) interface.
It is not TTL compatible. A lower percent change can
be accomodated with a series resistor. If unused, this
input may be left unconnected. For further information,
consult the related application note.
Margin Up:
When this input is asserted to GND, the
output voltage is increased by 5%. The input requires an
open-collector (open-drain) interface. It is not TTL
compatible. The percent change can be reduced with a
series resistor. If unused, this input may be left uncon-
nected. For further information, consult the related
application note.
Ordering Information
Package Options (PTH03010x
HH)(1)
Code
Description
Pkg Ref. (2)
AH
Horiz. T/H
(EUH)
AS
SMD, Standard (3)
(EUJ)
Output Voltage (PTH03010
Hxx)
Code
Voltage
W
0.8 V – 2.5 V (Adjust)
Notes:
(1) Add “T” to end of part number for tape and reel on SMD packages only.
(2) Reference the applicable package reference drawing for the dimensions and PC board layout
(3) “Standard” option specifies 63/37, Sn/Pb pin solder material.
PTH03010W —3.3-V Input
15-A, 3.3-V Input Non-Isolated
Wide-Output Adjust Power Module
SLTS203C – MAY 2003 – REVISED DECEMBER 2003
相關PDF資料
PDF描述
PTH03020WAZT 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03020WAZ 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03020WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03020WAST 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTH03030WAS 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PTH03010WAZ 功能描述:DC/DC轉換器 15A 3.3V-Inp Wide Output Adj Pwr Mdl RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH03010WAZT 功能描述:DC/DC轉換器 2.95-3.65Vin 15A 1.370" x0.620"x0.354 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH03010WXX 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module
PTH03010XAH 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module
PTH03010XAS 制造商:TI 制造商全稱:Texas Instruments 功能描述:15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module