參數資料
型號： PTH04000WAZ1
廠商： Texas Instruments, Inc.
元件分類： 基準電壓源/電流源
英文描述： RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述： 抗輻射高效，5安培開關穩壓器
文件頁數： 9/20頁
文件大?。?/td> 1347K
代理商： PTH04000WAZ1
www.ti.com
CAPACITOR RECOMMENDATIONS for the PTH04000W WIDE-OUTPUT
ADJUST POWER MODULES
Input Capacitor
Output Capacitors (Optional)
Ceramic Capacitors
Tantalum Capacitors
Capacitor Table
PTH04000W
SLTS247A–JUNE 2005–REVISED JULY 2005
The minimum required input capacitor(s) is 47-μF of ceramic capacitance, in either an X5R or X7R temperature
tolerance. The ceramic capacitors should be located within 0.5 inch (1,27 cm) of the regulator's input pins.
Electrolytic capacitors can also be used at the input, but only in addition to the required ceramic capacitance.
The minimum ripple current rating for nonceramic capacitors should be at least 200 mA rms. The ripple current
rating of electrolytic capacitors is a major consideration when they are used at the input.
When specifying regular tantalum capacitors for use at the input, a minimum voltage rating of 2 × (maximum dc
voltage + ac ripple) is highly recommended. This is standard practice to ensure reliability. Polymer-tantalum
capacitors are not affected by this requirement.
For improved ripple reduction on the input bus, additional ceramic capacitors can be used to complement the
minimum requirement.
For applications with load transients (sudden changes in load current), the regulator response benefits from
additional external output capacitance. The recommended output capacitance of 47 μF allows the module to
meet its transient response specification. A high-quality computer-grade electrolytic capacitor should be
adequate.
Electrolytic capacitors should be located close to the load circuit. These capacitors provide decoupling over the
frequency range, 2 kHz to 150 kHz. Aluminum electrolytic capacitors are suitable for ambient temperatures
above 0°C. For operation below 0°C, tantalum or Os-Con-type capacitors are recommended. When using one or
more nonceramic capacitors, the calculated equivalent ESR should be no lower than 4 m
(7 m
using the
manufacturer's maximum ESR for a single capacitor). A list of preferred low-ESR type capacitors are identified in
Table 3
.
Above 150 kHz the performance of aluminum electrolytic capacitors becomes less effective. To further improve
the reflected input ripple current, or the output transient response, multilayer ceramic capacitors must be added.
Ceramic capacitors have low ESR and their resonant frequency is higher than the bandwidth of the regulator.
When placed at the output, their combined ESR is not critical as long as the total value of ceramic capacitance
does not exceed 150 μF. Also, to prevent the formation of local resonances, do not exceed the maximum
number of capacitors specified in the capacitor table.
Additional tantalum type capacitors can be used at both the input and output, and are recommended for
applications where the ambient operating temperature can be less than 0°C. The AVX TPS, Sprague
593D/594/595, and Kemet T495/T510/T520 capacitors series are suggested over many other tantalum types due
to their rated surge, power dissipation, and ripple current capability. As a caution, many general-purpose
tantalum capacitors have considerably higher ESR and lower ripple current capability. These capacitors are also
less reliable as they have lower power dissipation capability and surge current ratings. Tantalum capacitors that
do not have a stated ESR or surge current rating are not recommended for power applications. When specifying
Os-Con and polymer-tantalum capacitors for the output, the minimum ESR limit is encountered well before the
maximum capacitance value is reached.
The capacitor table,
Table 3
, identifies the characteristics of capacitors from a number of vendors with
acceptable ESR and ripple current (rms) ratings. The recommended number of capacitors required at both the
input and output buses is identified for each capacitor type. This is not an extensive capacitor list. Capacitors
from other vendors are available with comparable specifications. Those listed are for guidance. The rms rating
and ESR (at 100 kHz) are critical parameters necessary to insure both optimum regulator performance and long
capacitor life.
9
相關PDF資料
PDF描述
PTH08000WAZ1 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
PTH08000WAZ2 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
PTH08000WAS1 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
PTH08000WAS2 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
PTH12060LAHT 10-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE
相關代理商/技術參數
參數描述
PTH04000WAZT 功能描述:DC/DC轉換器 3A 3.3/5V Input Adj Switching Regulator RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH04040 制造商:ARTESYN 制造商全稱:Artesyn Technologies 功能描述:DC-DC CONVERTERS POLA Non-isolated
PTH04040W 制造商:TI 制造商全稱:Texas Instruments 功能描述:60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE
PTH04040WAD 功能描述:DC/DC轉換器 60A 3.3/5V-In Wide Output Adj Pwr Mdl RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH04040WAH 功能描述:DC/DC轉換器 60A 3.3/5V-In Wide Output Adj Pwr Mdl RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*