- 您現在的位置：買賣IC網 > PDF目錄69252 > PTH04040WAS (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH04040WAS |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | DIP-20 |
| 文件頁數： | 11/25頁 |
| 文件大小： | 535K |
| 代理商： | PTH04040WAS |
D %
R
orR
=
U
D
499
-99.8kW
+
CI
VI
GND
MarginDown
Q2
Q1
+
MarginUp
0V
+VO
CO
RD
RU
(TopView)
PTH05010W
1
2
10
7
6
5
4
3
GND
R
0.1W,1%
SET
L
O
A
D
9
8
www.ti.com
SLTS238C – SEPTEMBER 2005 – REVISED JUNE 2010
MARGIN UP/DOWN CONTROLS
The PTHxx060, PTHxx010, PTHxx020, and PTHxx030 products incorporate Margin Up and Margin Down control
inputs. These controls allow the output voltage to be momentarily adjusted(1), either up or down, by a nominal
5%. This provides a convenient method for dynamically testing the operation of the load circuit over its supply
margin or range. It can also be used to verify the function of supply voltage supervisors. The ±5% change is
applied to the adjusted output voltage, as set by the external resistor, Rset at the Vo Adjust pin.
The 5% adjustment is made by pulling the appropriate margin control input directly to the GND terminal 2. A
low-leakage open-drain device, such as an n-channel MOSFET or p-channel JFET is recommended for this
purpose(3). Adjustments of less than 5% can also be accommodated by adding series resistors to the control
inputs. The value of the resistor can be selected from Table 4, or calculated using the following formula.
UP/DOWN ADJUST RESISTANCE CALCULATION
(4)
Where
Δ% = The desired amount of margin adjusted in percent.
NOTES
1. The Margin Up and Margin Down controls were not intended to be activated simultaneously. If they are
activated simultaneously, the effects on the output voltage may not completely cancel, resulting in the
possibility of a higher error in the output voltage set point.
2. The ground reference should be a direct connection to the module GND at pin 7 (pin 1 for the PTHxx050).
This produces a more accurate adjustment at the load circuit terminals. The transistors Q1 and Q2 should be
located close to the regulator.
3. The Margin Up and Margin Down control inputs are not compatible with devices that source voltage. This
includes TTL logic. These are analog inputs and should only be controlled with a true open-drain device
(preferably discrete MOSFET transistor). The device selected should have low off-state leakage current.
Each input sources 8 A when grounded, and has an open-circuit voltage of 0.8 V.
Table 4. Margin Up/Down Resistor Values
% ADJUST
5%
4%
3%
2%
1%
RU / RD
0 k
24.9 k
66.5 k
150.0 k
397.0 k
Figure 18. Margin Up/Down Application Schematic
Copyright 2005–2010, Texas Instruments Incorporated
19
Product Folder Link(s): PTH04040W
相關PDF資料 |
PDF描述 |
|---|---|
| PTH04040WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH04040WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH04070WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH04T220WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH04T220WAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH04040WAST | 功能描述:DC/DC轉換器 2.95-5.5Vin 0.8-3.6V 60A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH04040WAZ | 功能描述:DC/DC轉換器 60A 3.3/5V-In Wide Output Adj Pwr Mdl RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH04040WAZT | 功能描述:DC/DC轉換器 2.95-5.5Vin 0.8-3.6V 2.045" x1.045"x0.357 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH04070W | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-A, 3.3/5-V INPUT ADJUSTABLE SWITCHING REGULATOR |
| PTH04070W_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-A, 3.3/5-V INPUT ADJUSTABLE SWITCHING REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。