- 您現在的位置：買賣IC網 > PDF目錄69253 > PTH04T240WAS (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTH04T240WAS |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | PLASTIC, DIP-11 |
| 文件頁數： | 24/38頁 |
| 文件大?。?/td> | 964K |
| 代理商： | PTH04T240WAS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
VTRK (1 V/div)
VO1 (1 V/div)
VO2 (1 V/div)
T Time 20 ms/div
VTRK (1 V/div)
VO1 (1 V/div)
VO2 (1 V/div)
T Time 200
s/div
Prebias Startup Capability
SLTS276D – OCTOBER 2006 – REVISED JULY 2009 ...................................................................................................................................................... www.ti.com
Figure 25. Simultaneous Power Up
Figure 26. Simultaneous Power Down
With Auto-Track Control
A prebias startup condition occurs as a result of an external voltage being present at the output of a power
module prior to its output becoming active. This often occurs in complex digital systems when current from
another power source is backfed through a dual-supply logic component, such as an FPGA or ASIC. Another
path might be via clamp diodes as part of a dual-supply power-up sequencing arrangement. A prebias can cause
problems with power modules that incorporate synchronous rectifiers. This is because under most operating
conditions, these types of modules can sink as well as source output current.
The PTH family of power modules incorporate synchronous rectifiers, but does not sink current during startup(1),
or whenever the Inhibit pin is held low. However, to ensure satisfactory operation of this function, certain
conditions must be maintained(2). Figure 27 shows an application demonstrating the prebias startup capability.
The startup waveforms are shown in Figure 28. Note that the output current (IO) is negligible until the output
voltage rises above the voltage backfed through the intrinsic diodes.
The prebias start-up feature is not compatible with Auto-Track. When the module is under Auto-Track control, it
sinks current if the output voltage is below that of a back-feeding source. To ensure a pre-bias hold-off one of
two approaches must be followed when input power is applied to the module. The Auto-Track function must
either be disabled(3), or the module’s output held off (for at least 50 ms) using the Inhibit pin. Either approach
ensures that the Track pin voltage is above the set-point voltage at start up.
1. Startup includes the short delay (approximately 10 ms) prior to the output voltage rising, followed by the rise
of the output voltage under the module’s internal soft-start control. Startup is complete when the output
voltage has risen to either the set-point voltage or the voltage at the Track pin, whichever is lowest.
2. To ensure that the regulator does not sink current when power is first applied (even with a ground signal
applied to the Inhibit control pin), the input voltage must always be greater than the output voltage throughout
the power-up and power-down sequence.
3. The Auto-Track function can be disabled at power up by immediately applying a voltage to the module’s
Track pin that is greater than its set-point voltage. This can be easily accomplished by connecting the Track
pin to VI.
30
Copyright 2006–2009, Texas Instruments Incorporated
Product Folder Link(s): PTH04T240W PTH04T241W
相關PDF資料 |
PDF描述 |
|---|---|
| PTH04T241WAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH04T240WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH04T240WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05000WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH05000WAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH04T240WAST | 功能描述:DC/DC轉換器 10-A 2.2V to 5.5V Adj Pwr Mod RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH04T240WAZ | 功能描述:DC/DC轉換器 10-A 2.2V to 5.5V Adj Pwr Mod RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH04T240WAZT | 功能描述:DC/DC轉換器 10-A 2.2V to 5.5V Adj Pwr Mod RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH04T241W | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-A, 2.2-V to 5.5-V INPUT, NON-ISOLATED, WIDE-OUTPUT, ADJUSTABLE POWER MODULE WITH TURBOTRANS⑩ |
| PTH04T241WAD | 功能描述:DC/DC轉換器 10A 2.2V-5.5Vin Adj Pwr Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。