- 您現在的位置：買賣IC網 > PDF目錄378088 > PTH08000WAS1 (Texas Instruments, Inc.) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | PTH08000WAS1 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 抗輻射高效，5安培開關穩壓器 |
| 文件頁數： | 4/20頁 |
| 文件大小： | 1402K |
| 代理商： | PTH08000WAS1 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
www.ti.com
PIN ASSIGNMENT
PTH08000W
(TopView)
1
5
2
3
4
6
PTH08000W
SLTS248–JUNE 2005
TERMINAL FUNCTIONS
TERMINAL
NAME
I/O
DESCRIPTION
NO.
This is the common ground connection for the
V
I
and
V
O
power connections. It is also the 0-V
DC
reference for
the
Inhibit
,
V
O
Adjust
, and
Track
control inputs.
This is an analog control input that enables the output voltage to follow an external voltage. This pin becomes
active typically 20 ms after the input voltage has been applied, and allows direct control of the output voltage
from 0 V up to the nominal set-point voltage. Within this range, the output voltage follows the voltage at the
Track pin on a volt-for-volt basis. When the control voltage is raised above this range, the module regulates at
its set-point voltage. The feature allows the output voltage to rise simultaneously with other modules powered
from the same input bus. If unused, this input should be connected to V
I
.
during power up. For more information, consult the related application note literature number
.The positive input voltage power node to the module, which is referenced to common GND.
The Inhibit pin is an open-collector/drain-negative logic input that is referenced to GND. Applying a low-level
ground signal to this input disables the module's output. When the Inhibit control is active, the input current
drawn by the regulator is significantly reduced. If the Inhibit pin is left open-circuit, the module produces an
output voltage whenever a valid input source is applied.
A 1% resistor must be connected between this pin and GND (pin 1) to set the output voltage of the module
higher than 0.9 V. If left open-circuit, the output voltage defaults to this value. The temperature stability of the
resistor should be 100 ppm/°C (or better). The set-point range is from 0.9 V to 5.5 V. The electrical
specification table gives the standard resistor value for a number of common output voltages. See the
application information for further guidance.
The regulated positive power output with respect to the GND node.
GND
1
Track
2
I
V
I
3
I
Inhibit
4
I
V
O
Adjust
5
I
V
O
6
O
4
相關PDF資料 |
PDF描述 |
|---|---|
| PTH08000WAS2 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| PTH12060LAHT | 10-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| PTH12060WAHT | 10-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| PTH31002 | 30 Watts, 1.9-2.0 GHz 50-Ohm Power Hybrid |
| PTH32003 | 25 Watts, 1.9-2.0 GHz 50-Ohm High-Gain Power Hybrid |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTH08000WAS2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.25-A, WIDE INPUT, ADJUSTABLE SWITCHING REGULATOR |
| PTH08000WAST | 功能描述:DC/DC轉換器 2.25A 5/12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH08000WAZ | 功能描述:DC/DC轉換器 2.25A 5/12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTH08000WAZ1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.25-A, WIDE INPUT, ADJUSTABLE SWITCHING REGULATOR |
| PTH08000WAZ2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.25-A, WIDE INPUT, ADJUSTABLE SWITCHING REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。