參數資料
型號： PTH08000WAS2
廠商： Texas Instruments, Inc.
元件分類： 基準電壓源/電流源
英文描述： RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述： 抗輻射高效，5安培開關穩壓器
文件頁數： 15/20頁
文件大?。?/td> 1402K
代理商： PTH08000WAS2
www.ti.com
t-Time=4ms/div
V 1(1V/div)
O
V 2(1V/div)
O
V
(1V/div)
TRK
t-Time=400 s/div
V 1(1V/div)
O
V 2(1V/div)
O
V
(1V/div)
TRK
Typical Application
PTH08000W
SLTS248–JUNE 2005
Figure 15. Simultaneous Power Up With
Auto-Track Control
Figure 16. Simultaneous Power Down With
Auto-Track Control
The basic implementation of Auto-Track allows for simultaneous voltage sequencing of a number of Auto-Track
compliant modules. Connecting the
Track
inputs of two or more modules forces their track input to follow the
same collective RC-ramp waveform, and allows their power-up sequence to be coordinated from a common
Track control signal. This can be an open-collector (or open-drain) device, such as a power-up reset voltage
supervisor IC. See U3 in
Figure 14
.
To coordinate a power-up sequence, the Track control must first be pulled to ground potential. This should be
done at or before input power is applied to the modules. The ground signal should be maintained for at least
20 ms after input power has been applied. This brief period gives the modules time to complete their internal
soft-start initialization
(4)
, enabling them to produce an output voltage. A low-cost supply voltage supervisor IC,
that includes a built-in time delay, is an ideal component for automatically controlling the Track inputs at power
up.
Figure 14
shows how the TPS3808G50 supply voltage supervisor IC (U3) can be used to coordinate the
sequenced power up of two 5-V input Auto-Track modules. The output of the TPS3808G50 supervisor becomes
active above an input voltage of 0.8 V, enabling it to assert a ground signal to the common track control well
before the input voltage has reached the module's undervoltage lockout threshold. The ground signal is
maintained until approximately 27 ms after the input voltage has risen above U3's voltage threshold, which is
4.65 V. The 27-ms time period is controlled by the capacitor C3. The value of 4700 pF provides sufficient time
delay for the modules to complete their internal soft-start initialization. The output voltage of each module
remains at zero until the track control voltage is allowed to rise. When U3 removes the ground signal, the track
control voltage automatically rises. This causes the output voltage of each module to rise simultaneously with the
other modules, until each reaches its respective set-point voltage.
Figure 15
shows the output voltage waveforms from the circuit of
Figure 14
after input voltage is applied to the
circuit. The waveforms, V
O
1 and V
O
2, represent the output voltages from the two power modules, U1 (3.3 V) and
U2 (2.5 V), respectively. V
O
1 and V
O
2 are shown rising together to produce the desired simultaneous power-up
characteristic.
The same circuit also provides a power-down sequence. When the input voltage falls below U3's voltage
threshold, the ground signal is re-applied to the common track control. This pulls the track inputs to zero volts,
forcing the output of each module to follow. Power down is normally complete before the input voltage has fallen
below the modules' undervoltage lockout. This is an important constraint. Once the modules recognize that an
input voltage is no longer present, their outputs can no longer follow the voltage applied at their track input.
During a power-down sequence, the fall in the output voltage from the modules is limited by the Auto-Track slew
rate capability.
15
相關PDF資料
PDF描述
PTH12060LAHT 10-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE
PTH12060WAHT 10-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE
PTH31002 30 Watts, 1.9-2.0 GHz 50-Ohm Power Hybrid
PTH32003 25 Watts, 1.9-2.0 GHz 50-Ohm High-Gain Power Hybrid
PTN78060AAS-T 15-W, WIDE-INPUT ADJUSTABLE POSITIVE-TO-NEGATIVE VOLTAGE REGULATOR MODULE
相關代理商/技術參數
參數描述
PTH08000WAST 功能描述:DC/DC轉換器 2.25A 5/12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH08000WAZ 功能描述:DC/DC轉換器 2.25A 5/12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PTH08000WAZ1 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.25-A, WIDE INPUT, ADJUSTABLE SWITCHING REGULATOR
PTH08000WAZ2 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.25-A, WIDE INPUT, ADJUSTABLE SWITCHING REGULATOR
PTH08000WAZT 功能描述:DC/DC轉換器 2.25A 5/12V Input WideAdj Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*