- 您現在的位置：買賣IC網 > PDF目錄98066 > PTV05010WAH (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTV05010WAH |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | SIP-8 |
| 文件頁數： | 18/19頁 |
| 文件大?。?/td> | 462K |
| 代理商： | PTV05010WAH |
www.ti.com
Designing for Fast Load Transients
Adjusting the Output Voltage
R
SET + 10 kW
0.8 V
V
O * 0.8 V
* 2.49 kW
(1)
SLTS242A – FEBRUARY 2005 – REVISED OCTOBER 2005
The transient response of the dc/dc converter has been characterized using a load transient with a di/dt of
1 A/s. The typical voltage deviation for this load transient is given in the data sheet specification table using the
optional value of output capacitance. As the di/dt of a transient is increased, the response of a converter
regulation circuit ultimately depends on its output capacitor decoupling network. This is an inherent limitation with
any dc/dc converter once the speed of the transient exceeds its bandwidth capability. If the target application
specifies a higher di/dt or lower voltage deviation, the requirement can only be met with additional output
capacitor decoupling. In these cases, special attention must be paid to the type, value, and ESR of the
capacitors selected.
If the transient performance requirements exceed that specified in the data sheet, or the total amount of load
capacitance is above 3000 F, the selection of output capacitors becomes more important.
The VO Adjust control (pin 4) sets the output voltage of the PTV05010W product to a value over the range, 0.8 V
to 3.6 V. The adjustment method requires the addition of a single external resistor, RSET, that must be connected
directly between the VO Adjust and the regulator's output GND (pin 1 is recommended). Without an adjust
resistor, the output voltage is set to its lowest value. Table 2 gives the preferred value of the external resistor for
a number of standard voltages, along with the actual output voltage that this resistance value provides. Figure 6
shows the placement of the required resistor.
Table 2. Nearest Standard Values of RSET for Common Output Voltages
VO
RSET
VO
(Required)
(Standard Value)
(Actual)
3.3 V
698
3.309 V
2.5 V
2.21 k
2.502 V
2 V
4.12 k
2.010 V
1.8 V
5.49 k
1.803 V
1.5 V
8.87 k
1.504 V
1.2 V
17.4 k
1.202 V
1 V
36.5 k
1.005 V
0.8 V
Open
0.800 V
For other output voltages, the value of the required resistor can either be calculated or simply selected from the
range of values given in Table 3. Equation 1 may be used for calculating the adjust resistor value.
8
Copyright 2005, Texas Instruments Incorporated
Product Folder Link(s) :PTV05010W
相關PDF資料 |
PDF描述 |
|---|---|
| PTV08T250WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTV08T250WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTV12010WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTV12010WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PVX003A0X43-SRZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTV05020 | 制造商:EMERSON-NETWORKPOWER 制造商全稱:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTV05020W | 制造商:TI 制造商全稱:Texas Instruments 功能描述:18-A, 5-V INPUT NONISOLATED WIDE-OUTPUT ADJUST SIP MODULE |
| PTV05020WAD | 功能描述:DC/DC轉換器 64.8W 0.8-3.6V 18A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTV05020WAH | 功能描述:DC/DC轉換器 18A 5VInput Non-Iso Wide-Adj SIP Module RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PTV07RW25-187SA-S2 | 制造商:Amphenol Corporation 功能描述:TV 187C 187#23 SKT RECP HD |
發布緊急采購，3分鐘左右您將得到回復。