- 您現在的位置：買賣IC網 > PDF目錄98066 > PTV08T250WAH (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PTV08T250WAH |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 文件頁數： | 26/30頁 |
| 文件大?。?/td> | 795K |
| 代理商： | PTV08T250WAH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁
DEVICE INFORMATION
PIN1
)
V
-0.8
O
0.8
-7.135kW
(
R
=30.1
SET
x
www.ti.com .......................................................................................................................................... SLTS260E – OCTOBER 2005 – REVISED NOVEMBER 2008
PTV08T250W
(Top View)
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NAME
NO.
This is the common ground connection for the VI and VO power connections. It is also the 0 Vdc
GND
4, 5, 11, 12, 18, 19
reference for the control inputs.
VI
6, 7, 13, 14, 20, 21 The positive input voltage power node to the module, which is referenced to common GND.
VO
3, 10, 17
The regulated positive power output with respect to GND.
The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a
low-level ground signal to this input disables the module’s output and turns off the output voltage.
When the Inhibit control is active, the input current drawn by the regulator is significantly reduced. If
the Inhibit pin is left open-circuit, the module produces an output whenever the input voltage is above
Inhibit /
16
the UVLO threshold.
UVLO
This pin is also used for input undervoltage lockout (UVLO) programming. Connecting a resistor from
this pin to signal ground allows the ON threshold of the UVLO to be adjusted higher than the default
value. The hysterisis can also be independently reduced by connecting a second resistor from this pin
to VI. For further information, see the Application Information section.
A 1%, 0.05-W resistor must be connected between this pin and GND to set the output voltage higher
than the minimum value. The set-point range for the output voltage is from 0.8 V to 3.6 V. The resistor
VO Adjust
8
required for a given output voltage may be calculated from the following formula. If left open circuit, the
module output defaults to its lowest output voltage value. For further information on the adjustment
and/or trimming of the output voltage, see the related Application Information section.
The specification table gives the preferred resistor values for a number of standard output voltages.
The sense inputs allow the regulation circuit to compensate for voltage drop between the module and
+Sense
1
the load. For optimal voltage accuracy, +Sense should be connected to VO. If it is left open, a
low-value internal resistor ensures that the output remains in regulation.
For optimal voltage accuracy, –Sense should be connected to the ground return at the load. If it is left
–Sense
2
open, a low-value internal resistor ensures that the output remains in regulation.
This is an analog control input that allows the output voltage to follow another voltage during power up
and power down sequences. The pin is active from 0 V, up to the nominal set-point voltage. Within this
range, the module output follows the voltage at the Track pin on a volt-for-volt basis. When the control
Track
15
voltage is raised above this range, the module regulates at its nominal output voltage. If unused, this
input should be connected to VI for a faster power up. For further information, see the related
Application Information section.
This input pin adjusts the transient response of the regulator. For a given value of output capacitance,
a reduction in peak output voltage deviation and increased system stability is achieved by placing a
resistor between this pin and +Sense. A 1%, 0.05-W resistor must be connected between this pin and
TurboTrans
9
+Sense to activate the TurboTrans feature. Suggested placement of this resistor is within 1 cm from
pin 9. The resistor value required can be selected from the TurboTrans resistor table. If unused, this
input pin should be left open-circuit. For further information, see the related Application Information
section.
Copyright 2005–2008, Texas Instruments Incorporated
5
Product Folder Link(s): PTV08T250W
相關PDF資料 |
PDF描述 |
|---|---|
| PTV08T250WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTV12010WAD | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTV12010WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PVX003A0X43-SRZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PVX006A0X43-SRZ | DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PTV09 | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:9 mm Potentiometer |
| PTV09A-2015F-A102 | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:9 mm Potentiometer |
| PTV09A-2015F-A202 | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:9 mm Potentiometer |
| PTV09A-2015F-A502 | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:9 mm Potentiometer |
| PTV09A-2015F-B102 | 制造商:BOURNS 制造商全稱:Bourns Electronic Solutions 功能描述:9 mm Potentiometer |
發布緊急采購，3分鐘左右您將得到回復。