- 您現在的位置：買賣IC網 > PDF目錄361297 > QLS30ZB QLS30 Series . 30A Quarter-Brick DC/DC Converter 48V Input 1.8V, 1.5V, 1.2V Output PDF資料下載
參數資料
| 型號： | QLS30ZB |
| 英文描述： | QLS30 Series . 30A Quarter-Brick DC/DC Converter 48V Input 1.8V, 1.5V, 1.2V Output |
| 中文描述： | QLS30系列。 30A條四分之一磚DC / DC轉換器48V輸入1.8或1.5V，1.2V的輸出 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 143K |
| 代理商： | QLS30ZB |
QLS30 Series – 30A Quarter-Brick DC/DC Converter
48V Input
1.8V, 1.5V, 1.2V Output
Data Sheet
REV. 10/01 Page
6 of 8
k
(1)
V
where A and B are constants from the table
below, and
Δ
V is the absolute value of the desired
change in the output voltage in Volts.
Model
Trim up
A
0.57
0.283
0.5928
Trim down
A
0.2711
0.065
0.5686
B
1
B
QLS30ZB
QLS30ZA
QLS30ZY
1.4676
0.352
2.0422
0.121
3.01
Inductrial Standard Positive Trim (suffix –T)
The -T option units trim up with a resistor from the
TRIM pin to the +Sense pin and trim down with a
resistor from the TRIM pin to the –Sense pin as
shown in the Figure 9.
Fig.9 QLS30 series positive trim schematic
The equations below determine the trim resistor
value required to achieve a
Δ
V change in the
output voltage.
%
+
%
V
+
=
%
2
100
225
100
V
.
%)
100
(
11
.
V
V
V
Vout
R
UP
,k
=
2
%
11
.
R
DOWN
, k
For QLS30ZY use the following equations.
%
V
+
=
225
.
%)
100
(
11
.
V
Vout
R
UP
,K
=
2
1
%
2
100
V
11
.
R
DOWN
,K
where
Δ
V% is the output voltage change
expressed in percents of the nominal output
voltage, Vout.
Notes:
1. When the output voltage is trimmed up, the
output power from the converter must not
exceed its maximum rating. The power is
determined by measuring the output voltage
on the output pins, and multiplying it by the
output current.
2. In order to avoid creating apparent load
regulation degradation, it is important that the
trim resistors are connected directly to the
remote sense pins, and not to the load or to
traces going to the load.
3. The QLS30 series converters will trim down
further than the 10% limit. In general, this is
permissible. The user must confirm that the
results are acceptable in the application.
Safety Considerations
The QLS30 series converters feature 1500 Volt
DC isolation from input to output. The input to
output resistance is greater than 10MOhm.
These converters are provided with Basic
insulation between input and output circuits
according to all IEC60950 based standards.
Nevertheless, if the system using the converter
needs to receive safety agency approval, certain
rules must be followed in the design of the
system. In particular, all of the creepage and
clearance requirements of the end-use safety
requirements must be observed. These
documents include UL60950, CSA60950-00 and
EN60950, although other additional requirements
may be needed for user’s specific applications.
The QLS30 series converters have no internal
fuse. An external fuse must be provided to
protect the system from catastrophic failure, as
illustrated in Figure 7. The fuse with a rating of
4A or less is recommended. The user can select
a lower rating fuse based upon the highest inrush
transient at the maximum input voltage and the
maximum input current of the converter at the
minimum input voltage. Both input traces and the
TRIM
相關PDF資料 |
PDF描述 |
|---|---|
| QLS30ZY | QLS30 Series . 30A Quarter-Brick DC/DC Converter 48V Input 1.8V, 1.5V, 1.2V Output |
| QLSI-STANDARD-CELL | Microcontroller |
| QLU2108-PQ208C | Telecommunication IC |
| QLU22108-PT280C | Telecommunication IC |
| QLUM2208-PQ208C | Telecommunication IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QLS30ZB-N | 制造商:Power-One 功能描述:- Bulk |
| QLS30ZB-NT | 功能描述:DC/DC轉換器 1.8V/30A NEG-LOGIC QUARTER BRICK CONVTR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| QLS30ZB-NT7 | 制造商:Power-One 功能描述:1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| QLS30ZB-NT8 | 制造商:Power-One 功能描述: |
| QLS30ZB-NTS1 | 制造商:Power-One 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。