- 您現在的位置：買賣IC網 > PDF目錄1966 > QLX4600SIQSR (Intersil)IC EQUALIZER REC 6.25GBPS 46QFN PDF資料下載
參數資料
| 型號： | QLX4600SIQSR |
| 廠商： | Intersil |
| 文件頁數： | 21/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC EQUALIZER REC 6.25GBPS 46QFN |
| 標準包裝： | 100 |
| 系列： | QLx™ |
| 應用： | 銅電纜模塊 |
| 電源電壓： | 1.1 V ~ 1.3 V |
| 封裝/外殼： | 46-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 46-TQFN |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
7
FN6979.1
November 19, 2009
Line Silence-to-Data
Response Time
tSD
Time to transition from line silence mode
(muted output) to active data on 20m
24AWG standard twin-axial cable at 5Gb/s
20
ns
Time from first bit of ALIGN(0) for SAS
OOB signaling to 450mVP-P output;
Meritec 24AWG 20m; 3Gb/s
19
ns
Timing Difference (SAS)
|tDS - tSD| For SAS OOB signaling support; Meritec
24AWG 20m
5ns
NOTES:
3. After channel loss, differential amplitudes at QLx4600-S30 inputs must meet the input voltage range specified in “Absolute
4. Temperature = +25°C, VDD = 1.2V.
5. Output residual jitter is the difference between the total jitter at the lane extender output and the total jitter of the transmitted
signal (as measured at the input to the channel). Total jitter (TJ) is DJPP + 14.1 x RJRMS.
6. Measured using a PRBS 27-1 pattern. Deterministic jitter at the input to the lane extender is due to frequency-dependent,
media-induced loss only.
7. Rise and fall times measured using a 1GHz clock with a 20ps edge rate.
8. For active data mode, cable input amplitude is 400mVP-P (differential) or greater. For line silence mode, cable input amplitude
is 20mVP-P (differential) or less.
9. Measured differentially across the data source.
10. During line silence, transmitter noise in excess of this voltage range may result in differential output amplitudes from the
QLx4600 that are greater than 20mVP-P.
11. The data pattern preceding line silence mode is comprised of the PCIe electrical idle ordered set (EIOS). The data pattern
following line silence mode is comprised of the PCIe electrical idle exit sequence (EIES).
12. The data pattern preceding or following line silence mode is comprised of the SAS-2 ALIGN (0) sequence for OOB signaling at
3Gb/s, and amplitude of 800mVP-P.
Electrical Specifications Typical values are at VDD = 1.2V, TA = +25°C, and VIN = 800mVP-P, unless otherwise noted.
VDD = 1.1V to 1.3V, TA = 0°C to +70°C. (Continued)
PARAMETERS
SYMBOL
CONDITION
MIN
TYP
MAX
UNITS NOTES
Serial Bus Timing Characteristics
PARAMETER
SYMBOL
CONDITION
MIN
TYP
MAX
UNITS
CLK Setup Time
tSCK
From the falling edge of ENB
10
ns
DI Setup Time
tSDI
Prior to the rising edge of CLK
10
ns
DI Hold Time
tHDI
From the rising edge of CLK
6
ns
ENB ‘HIGH’
tHEN
From the falling edge of the last data bit’s CLK
10
ns
Boost Setting Operational
tD
From ENB ‘HIGH’
10
ns
DO Hold Time
tCQ
From the rising edge of CLK to DO transition
12
ns
Clock Rate
fCLK
Reference clock for serial bus EQ programming
20
MHz
QLx4600-S30
相關PDF資料 |
PDF描述 |
|---|---|
| R5F100GEAFB#V0 | MCU 16BIT 64KB FLASH 48LQFP |
| R5F2135CMNFP#V0 | IC MICROCONTROLLER |
| R5F562N8ADBG#U0 | MCU 32BIT FLASH 512KROM 176LFBGA |
| R5F5630ADDFB#V0 | MCU RX630 768KB FLASH 144-LQFP |
| R5F72167GDFA#V0 | MCU 1MB FLASH 128K 176-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QLX4600SIQT7 | 功能描述:接口 - 專用 6 GBS QD CH LANE EXTENDER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QLX4600-SL30 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Lane Extender |
| QLZ06 0012-2513 | 制造商:ebm-papst Inc 功能描述: |
| QLZ06 0018-2518 | 制造商:ebm-papst Inc 功能描述: |
| QLZ06 0600-2513 | 制造商:Ebm-Papst Industries 功能描述:Bulk |
發布緊急采購，3分鐘左右您將得到回復。