參數資料
型號: RC4190N
廠商: Raytheon Company
元件分類: 基準電壓源/電流源
英文描述: RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述: 抗輻射高效,5安培開關穩壓器
文件頁數: 21/25頁
文件大?。?/td> 174K
代理商: RC4190N
RC4190
PRODUCT SPECIFICATION
21
3.
Note the approximate air gap at I
MAX
for the selected
core, and order the core with the gap. (If the gapping is
done by the user, remember that a washer spacer results
in an air gap of twice the washer thickness, because two
gaps will be created, one at the center post and one at the
rim, like taking two bites from a doughnut.)
4.
If the required inductance is equal to the indicated value
on the graph, then wind the core with the number of
turns shown in table of sizes. The turns given are the
maximum number for that gauge of wire that can be
easily wound in the cores winding area.
5.
If the required inductance is less than the value indicated
on the graph, a simple calculation must be done to find
the adjusted number of turns. Find A
L
(inductance
index) for a specific air gap.
in Henrys/turn
2
Then divide the required inductance value by A
L
to give
the actual turns squared, and take the square root to find
the actual turns needed.
If the actual number of turns is significantly less than the
number from the table then the wire size can be
increased to use up the left-over winding area and
reduce resistive losses.
6.
Wind and gap the core as per calculations, and measure
the value with an inductance meter. Some adjustment of
the number of turns may be
necessary.
The saturation characteristics may be checked with the
inductor wired into the switching regulator application
circuit. To do so, build and power up the circuit. Then
(recommend Tektronix P6042 or equivalent) around the
inductor lead and monitor the current in the inductor.
Draw the maximum load current from the application
circuit so that the regulator is running at close to full
duty cycle.
Compare the waveform you see to those pictured in
Figure 28.
Check for saturation at the highest expected ambient
temperature.
7.
After the operation in circuit has been checked,
reassemble and pot the core using a potting compound
recommended by the manufacturer.
If the core material differs greatly in magnetic character-
istics from the standard power material shown in Figure
22, then the following general equation can be used to
help in winding and gapping. This equation can be used
for any core geometry, such as an E-E core.
2
)
Ae
(
(
)
le
(
)
ue
(
)
=
Where: N = number of turns
Ae = core area from data sheet (in cm2)
le = magnetic path length from data sheet (in cm)
ue = permeability of core from manufacturer's graph
g = center post air gap (in cm)
Manufacturers
Below is a list of several pot core manufacturers:
Ferroxcube Company
5083 Kings Highway
Saugerties, NY 12477
Indiana General Electronics
Keasley, NJ 08832
Siemens Company
186 Wood Avenue South
Iselin, NJ 08830
Stackpole Company
201 Stackpole Street
St. Mary, PA 15857
TDK Electronics
13-1-Chome
Nihonbaski, Chuo-ku, Tokyo
Turns
)
L indicated
A
L
=
ActualTurns
L
)
L reA
=
L
X
-1.26
(
)
10
8
=
Figure 28. Inductor Current Waveforms
0
I
MAX
65-3464-08
Proper Operation
(Waveform is Fairly Linear)
Improper Operation
(Waveform is Nonlinear, Inductor
Is Saturating)
0
I
MAX
相關PDF資料
PDF描述
RC5033 Adjustanble Sychronous DC-DC Converter
RC5033M Adjustanble Sychronous DC-DC Converter
RC5041 Programmable DC-DC Converter for Pentium P55C, K6 and 6x86MX (M2) Processors
RC5041M Programmable DC-DC Converter for Pentium P55C, K6 and 6x86MX (M2) Processors
RC5042 Programmable DC-DC Converter
相關代理商/技術參數
參數描述
RC4191 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
RC4191D/883 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller
RC4191M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller
RC4191N 制造商:. 功能描述:
RC4192 制造商:未知廠家 制造商全稱:未知廠家 功能描述: