- 您現在的位置：買賣IC網 > PDF目錄373259 > REG103-3 DMOS 500mA Low Dropout (LDO) Regulator PDF資料下載
參數資料
| 型號： | REG103-3 |
| 英文描述： | DMOS 500mA Low Dropout (LDO) Regulator |
| 中文描述： | 的DMOS 500mA的低壓降（LDO）穩壓器 |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 264K |
| 代理商： | REG103-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁
REG103
SBVS010A
10
0
2
4
6
8
10
12
14
16
100
10
1
0.1
0.01
0.001
E
μ
A
Enable Voltage
FIGURE 5. ENABLE Pin Current versus Applied Voltage.
REG103
ERROR
+5V
10k
Pull-up
3
ENABLE
SO-8 Package
Only
6
Open
Drain
μ
P
FIGURE 6. ERROR Pin Typical Fault-Monitoring Circuit.
ENABLE
The ENABLE pin allows the regulator to be turned on and
off. This pin is active HIGH and compatible with standard
TTL-CMOS levels. Inputs below 0.5V (max) turn the regu-
lator off and all circuitry is disabled. Under this condition,
ground pin current drops to approximately 0.5
μ
A. When not
used, the ENABLE pin may be connected to V
IN
.
Internal to the part, the ENABLE pin is connected to an
input resistor-zener diode circuit, as shown in Figure 4,
creating a nonlinear input impedance. The ENABLE Pin
Current versus Applied Voltage relationship is shown in
Figure 5. When the ENABLE pin is connected to a voltage
greater than 10V, a series resistor may be used to limit the
current.
ENABLE
V
Z
= 10V
175k
FIGURE 4. ENABLE Pin Equivalent Input Circuit.
FIGURE 3. Foldback Current Limit and Boost Circuit.
0
100
200
300
400
500
600
700
800
3.5
3
2.5
2
1.5
1
0.5
0
O
Output Current (mA)
REG103
V
IN
0.1
μ
F
Gnd
R
BOOST
V
OUT
+
0.1
μ
F
(1)
Load
+
(1) Optional.
(a) Foldback Current Limit of the REG103-3.3 at 25
°
C.
(b) Foldback Current Boost Circuit.
ERROR FLAG
The error indication pin, only available on the SO-8 package
version, provides a fault indication out-of-regulation condi-
tion. During a fault condition, ERROR is pulled LOW by an
open drain output device. The pin voltage, in the fault state,
is typically less than 0.2V at 500
μ
A.
A fault condition is indicated when the output voltage differs
(either above or below) from the specified value by approxi-
mately 10%. Figure 6 shows a typical fault-monitoring
application.
OUTPUT NOISE
A precision band-gap reference is used for the internal
reference voltage, V
REF
, for the REG103. This reference is
the dominant noise source within the REG103. It generates
approximately 45
μ
Vrms in the 10Hz to 100kHz bandwidth
at the reference output. The regulator control loop gains up
the reference noise, so that the noise voltage of the regulator
is approximately given by:
V
VrmsR
μ
45
R
2
R
Vrms
μ
45
V
V
N
OUT
REF
=
+
=
1
2
相關PDF資料 |
PDF描述 |
|---|---|
| REG103-33 | DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-5 | DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-A | DMOS 500mA Low Dropout (LDO) Regulator |
| REG101-25 | DMOS 100mA Low Dropout (LDO) Regulator |
| REG101-28 | DMOS 100mA Low Dropout (LDO) Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| REG103-33 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DMOS 500mA Low Dropout (LDO) Regulator |
| REG103-A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DMOS 500mA Low Dropout (LDO) Regulator |
| REG103FA | 制造商:BB 制造商全稱:BB 功能描述:DMOS 500mA Low Dropout Regulator |
| REG103FA-2.5 | 功能描述:IC REG LDO 2.5V .5A 5-DDPAK RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3V 輸入電壓:最高 5.5V 電壓 - 壓降（標準）:0.4V @ 300mA 穩壓器數量:1 電流 - 輸出:300mA（最小值） 電流 - 限制（最?。?350mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:TO-236-3，SC-59，SOT-23-3 供應商設備封裝:SC-59-3 包裝:Digi-Reel® 產品目錄頁面:1134 (CN2011-ZH PDF) 其它名稱:AP130-30WLDIDKR |
發布緊急采購，3分鐘左右您將得到回復。