- 您現在的位置：買賣IC網 > PDF目錄225035 > REG103UA-3.3/2K5 (TEXAS INSTRUMENTS INC) 3.3 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO8 PDF資料下載
參數資料
| 型號： | REG103UA-3.3/2K5 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 固定正電壓單路輸出LDO穩壓器 |
| 英文描述： | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO8 |
| 封裝： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 26/26頁 |
| 文件大?。?/td> | 830K |
| 代理商： | REG103UA-3.3/2K5 |
REG103
9
SBVS010D
0
2
4
6
8
10
12
14
16
100
10
1
0.1
0.01
0.001
Enable
Current
(
A)
Enable Voltage
FIGURE 5. ENABLE Pin Current versus Applied Voltage.
REG103
ERROR
+5V
10k
Pull-up
3
ENABLE
SO-8 Package
Only
6
Open
Drain
P
FIGURE 6. ERROR Pin Typical Fault-Monitoring Circuit.
ENABLE
The ENABLE pin allows the regulator to be turned on and
off. This pin is active HIGH and compatible with standard
TTL-CMOS levels. Inputs below 0.5V (max) turn the regu-
lator off and all circuitry is disabled. Under this condition,
ground pin current drops to approximately 0.5
A. When not
used, the ENABLE pin may be connected to VIN.
Internal to the part, the ENABLE pin is connected to an
input resistor-zener diode circuit, as shown in Figure 4,
creating a nonlinear input impedance. The ENABLE Pin
Current versus Applied Voltage relationship is shown in
Figure 5. When the ENABLE pin is connected to a voltage
greater than 10V, a series resistor may be used to limit the
current.
ENABLE
V
Z = 10V
175k
FIGURE 4. ENABLE Pin Equivalent Input Circuit.
FIGURE 3. Foldback Current Limit and Boost Circuit.
0
100
200
300
400
500
600
700
800
3.5
3
2.5
2
1.5
1
0.5
0
Output
Voltage
(V)
Output Current (mA)
REG103
V
IN
0.1
F
Gnd
R
BOOST
V
OUT
+
0.1
F(1)
Load
+
(1) Optional.
(a) Foldback Current Limit of the REG103-3.3 at 25
°C.
(b) Foldback Current Boost Circuit.
ERROR FLAG
The error indication pin, only available on the SO-8 package
version, provides a fault indication out-of-regulation condi-
tion. During a fault condition, ERROR is pulled LOW by an
open drain output device. The pin voltage, in the fault state,
is typically less than 0.2V at 500
A.
A fault condition is indicated when the output voltage differs
(either above or below) from the specified value by approxi-
mately 10%. Figure 6 shows a typical fault-monitoring
application.
OUTPUT NOISE
A precision band-gap reference is used for the internal
reference voltage, VREF, for the REG103. This reference is
the dominant noise source within the REG103. It generates
approximately 45
Vrms in the 10Hz to 100kHz bandwidth
at the reference output. The regulator control loop gains up
the reference noise, so that the noise voltage of the regulator
is approximately given by:
V
Vrms
RR
R
Vrms
V
N
OUT
REF
=
+
=
45
2
45
12
相關PDF資料 |
PDF描述 |
|---|---|
| REG103UA-3.3 | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO8 |
| REG103UA-3 | 3 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO8 |
| REG103UA-5/2K5 | 5 V FIXED POSITIVE LDO REGULATOR, 0.25 V DROPOUT, PDSO8 |
| REG103FA-AKTTTG3 | 1.295 V-5.5 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PSSO5 |
| REG104FA-2.7/500 | 2.7 V FIXED POSITIVE LDO REGULATOR, 0.46 V DROPOUT, PSSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| REG103UA-3G4 | 功能描述:低壓差穩壓器 - LDO Sgl Output Lo Noise Fast Trans Resp RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| REG103UA4 | 制造商:Texas Instruments 功能描述: |
| REG103UA5 | 制造商:TI 功能描述:Pb Free |
| REG103UA-5 | 功能描述:低壓差穩壓器 - LDO DMOS 500mA LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| REG103UA-5/2K5 | 功能描述:低壓差穩壓器 - LDO DMOS 500mA LDO Reg RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。