- 您現在的位置：買賣IC網 > PDF目錄373262 > RF1K4908696 TRANSISTOR | MOSFET | MATCHED PAIR | N-CHANNEL | 30V V(BR)DSS | 3.5A I(D) | SO PDF資料下載
參數資料
| 型號： | RF1K4908696 |
| 英文描述： | TRANSISTOR | MOSFET | MATCHED PAIR | N-CHANNEL | 30V V(BR)DSS | 3.5A I(D) | SO |
| 中文描述： | 晶體管| MOSFET的|配對| N溝道| 30V的五（巴西）直| 3.5AI（四）|蘇 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 262K |
| 代理商： | RF1K4908696 |
2002 Fairchild Semiconductor Corporation
RF1K49093 Rev. B
Soldering Precautions
The soldering process creates a considerable thermal stress
on any semiconductor component. The melting temperature
of solder is higher than the maximum rated temperature of
the device. The amount of time the device is heated to a high
temperature should be minimized to assure device reliability.
Therefore, the following precautions should always be
observed in order to minimize the thermal stress to which the
devices are subjected.
1. Always preheat the device.
2. The delta temperature between the preheat and soldering
should always be less than 100
o
C. Failure to preheat the
device can result in excessive thermal stress which can
damage the device.
3. The maximum temperature gradient should be less than 5
o
C
per second when changing from preheating to soldering.
4. The peak temperature in the soldering process should be
at least 30
o
C higher than the melting point of the solder
chosen.
5. The maximum soldering temperature and time must not
exceed 260
o
C for 10 seconds on the leads and case of
the device.
6. After soldering is complete, the device should be allowed
to cool naturally for at least three minutes, as forced cool-
ing will increase the temperature gradient and may result
in latent failure due to mechanical stress.
7. During cooling, mechanical stress or shock should be
avoided.
FIGURE 18. SWITCHING TIME TEST CIRCUIT
FIGURE 19. RESISTIVE SWITCHING WAVEFORMS
FIGURE 20. GATE CHARGE TEST CIRCUIT
FIGURE 21. GATE CHARGE WAVEFORMS
Test Circuits and Waveforms
(Continued)
V
GS
R
L
R
G
DUT
+
-
V
DD
t
d(ON)
t
r
90%
10%
V
DS
90%
t
f
t
d(OFF)
t
OFF
90%
50%
50%
10%
PULSE WIDTH
V
GS
0
t
ON
10%
0
0.3
μ
F
12V
BATTERY
50k
+V
DS
S
DUT
D
G
I
g(REF)
0
(ISOLATED
SUPPLY)
-V
DS
0.2
μ
F
CURRENT
REGULATOR
I
D
CURRENT
SAMPLING
RESISTOR
I
G
CURRENT
SAMPLING
RESISTOR
DUT
V
DD
Q
g(TH)
V
GS
= -1V
Q
g(-5)
V
GS
= -5V
Q
g(TOT)
V
GS
= -10V
V
DS
-V
GS
I
g(REF)
0
0
RF1K49093
相關PDF資料 |
PDF描述 |
|---|---|
| RF1K4908896 | TRANSISTOR | MOSFET | MATCHED PAIR | N-CHANNEL | 30V V(BR)DSS | 3.5A I(D) | SO |
| RF1S25N06SM9A | TRANSISTOR | MOSFET | N-CHANNEL | 60V V(BR)DSS | 25A I(D) | TO-263AB |
| RF1S30P05SM9A | TRANSISTOR | MOSFET | P-CHANNEL | 50V V(BR)DSS | 30A I(D) | TO-263AB |
| RF1S30P06SM9A | TRANSISTOR | MOSFET | P-CHANNEL | 60V V(BR)DSS | 30A I(D) | TO-263AB |
| RF1S40N10LESM9A | TRANSISTOR | MOSFET | N-CHANNEL | 100V V(BR)DSS | 40A I(D) | TO-263AB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF1K4908696136 | 功能描述:MOSFET RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| RF1K49088 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:3.5A, 30V, 0.06 Ohm, Logic Level, Dual N-Channel LittleFET⑩ Power MOSFET |
| RF1K4908896 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET | MATCHED PAIR | N-CHANNEL | 30V V(BR)DSS | 3.5A I(D) | SO |
| RF1K49090 | 功能描述:MOSFET RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| RF1K4909096 | 功能描述:MOSFET RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。