參數資料
型號： RF2444
廠商： RF MICRO DEVICES INC
元件分類： 無繩電話/電話
英文描述： HIGH FREQUENCY LNA/MIXER
中文描述： TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PDSO16
封裝： SSOP-16
文件頁數： 6/16頁
文件大?。?/td> 225K
代理商： RF2444
8-58
RF2444
Rev A3 010717
8
F
T heory of Operation
RX
15 dB Gain
IL = 3-4 dB
2.4 to 2.483 GHz
LNA
Dual Gain Modes
-5 dB and +10 dB
Gain
Select
RF2444
SSOP-16 EPP
Filter
2.4 to 2.483 GHz
SAW
IL = 10 dB max
RX
TX
15 dB
15 dB
IF Amp
-15 dB to 35 dB Gain
DATA Q
OUT Q
RSSI
DATA I
OUT I
Filter
Filter
Selectable LPF
TX
Σ
I INPUT
Q INPUT
15 dB Gain
Range
+45°
-45°
IL = 3-4 dB
2.4 to 2.483 GHz
10 dBm
PA Driver
RF2938
TQFP-48 EPP
VGC1
VGC2
Base Band Amp.
Active Selectable LPF
(f
C
= 1 MHz to 40 MHz)
0-30 dB Gain
RF Micro Devices
2.4 GHz ISM Chipset
23 dBm or 33 dBm
External PA
RF2126
IF
VCO
RF
VCO
RF2517
SSOP-28
Dual
Frequency
Synthesizer
Discrete
Pin Diode
Figure 1. Entire Chipset Functional Block Diagram
The RF2444 contains the LNA/Mixer for this chipset.
The LNA is made from two stages including a common
emitter amplifier stage with a power gain of 13dB and
an attenuator which has an insertion loss of 3dB in
high gain mode, and 17dB in low gain mode. The
attenuator was put after the LNA so that system noise
figure degradation would be minimized. A single gain
stage was used prior to the image filter to maximize
IP3 which minimizes the risk of large out-of-bad signals
jamming the desired signal.
The mixer on the RF2444 is also two stages. The first
stage is a common emitter amp used to boost the total
power gain prior to the lossy SAW filter, to convert to a
differential signal to the input of the mixer, and to
improve the noise figure of the mixer. The second
stage is a double balanced mixer whose output is dif-
ferential open collector. It is recommended that a “cur-
rent combiner” is used (as shown in figure 2) at the
mixer output to maximize conversion gain, but other
loads can also be used. The current combiner is used
to do a differential to single ended conversion for the
SAW filter. C1, C2 and L1 are used to tune the circuit
for a specific IF frequency. L2 is a choke to supply DC
current to the mixer that is also used as a tuning ele-
ment, along with C3, to match to the SAW filter’s input
impedance. RL is the SAW filter’s input impedance.
The mixer power conversion gain is +19dB when R1 is
set to 1k
. The conversion gain can be adjusted up
~5dB or down ~7dB by changing the value of R1.
Once R1 is chosen, L2 and C3 can be used to tune the
output for the SAW filter.
The cascaded power gain of the LNA/Mixer is 29dB,
which after insertion loss in the image filter (~3dB) and
IF SAW filter (~10dB), still gives 16dB of gain prior to
the IF amps. Because of this, the noise figure of the IF
amps should not significantly degrade system noise
figure.
The LNA input should be matched for a good return
loss for optimum gain and noise figure. To allow the
designer to match each of these ports, 2-port s-param-
eter data is available for the LNA, and 1-port data is
available for MIXER IN and LO IN.
L1
R1
C1
C2
L2
C3
RL
VCC
OUT
Open Collector
Mixer Output
Figure 2. Current Combiner for Mixer Load
相關PDF資料
PDF描述
RF2449 CDMA/FM LOW NOISE AMPLIFIER/MIXER 900MHZ DOWNCONVERTER
RF2451 3V LOW NOISE AMPLIFIER
RF2456 CDMA/FM DOWNCONVERTER
RF2459 3V PCS DOWNCONVERTER
RF2460 PCS CDMA LOW NOISE AMPLIFIER/MIXER 1500MHZ TO 2200MHZ DOWNCONVERTER
相關代理商/技術參數
參數描述
RF2449 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:CDMA/FM LOW NOISE AMPLIFIER/MIXER 900MHZ DOWNCONVERTER
RF2450 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
RF2451 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:3V LOW NOISE AMPLIFIER
RF2454 制造商:International Rectifier 功能描述:
RF2456 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:CDMA/FM DOWNCONVERTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*