參數資料
型號： RF2512
廠商： RF MICRO DEVICES INC
元件分類： 通信及網絡
英文描述： UHF TRANSMITTER
中文描述： SPECIALTY TELECOM CIRCUIT, PDSO24
封裝： PLASTIC, SSOP-24
文件頁數： 7/14頁
文件大?。?/td> 313K
代理商： RF2512
11-17
RF2512
Rev B9 010509
11
T
tance is set by the loop filter output voltage through a
4k
resistor.
To tune the VCO the designer only needs to calculate
the value of the inductors connected to pins 18 and 20
(RESNTR- and RESNTR+). The inductor value is
determined by the following equation.
In this equation,
f
is the desired operating frequency
and
L
is the value of the inductor required. The value
C
is the amount of capacitance presented by the varac-
tor, capacitor and parasitics. The factor of one-half is
due to the inductors being in each leg.
The setup of the VCO can be summarized as follows.
First, open the loop. Next, get the VCO to run on the
desired frequency by selecting the proper inductor and
capacitor values. The capacitor value will need to
include the varactor and circuit parasitics. After the
VCO is running at the desired frequency, then set the
VCO sensitivity.
The sensitivity is determined by connecting the control
voltage input point to ground and noting the frequency.
Then connect the same point to the supply and again
note the frequency. The difference between these two
frequencies divided by the supply voltage is the VCO
sensitivity expressed in Hz/V. Increasing the inductor
value
while
decreasing
increase the sensitivity. Decreasing the inductor value
while increasing the capacitor value will lower the sen-
sitivity.
the
capacitor
value
will
When increasing or decreasing component values,
make sure that the center frequency remains constant.
Finally, close the loop.
External to the part, the designer needs to implement a
loop filter
to complete the PLL. The loop filter converts
the output of the charge pump into a voltage that is
used to control the VCO. Internally, the VCO is con-
nected to the charge pump output through a 4k
resis-
tor. The loop filter is then connected in parallel to this
point at pin 23 (LOOP FLT). This limits the loop filter
topology to a second order filter usually consisting of a
shunt capacitor and a shunt series RC. A passive filter
is most common, as it is a low cost and low noise
design. An additional pole could be used for reducing
the reference spurs, however there is not a way to add
the series resistor. This should not be a reason for con-
cern however.
The schematic of the loop filter is
The transfer function is
where the time constants are defined as
and
The frequency at which unity gain occurs is given by
This is also the loop bandwidth.
If the phase margin (PM) and the loop bandwidth
(
ω
LBW
) are known, it is possible to calculate the time
constants. These are found using the equations
and
RESNTR-
RESNTR+
LOOP
FLT
4 k
L
L
L
2
π
f
----------------
2
1
C
---
1
2
--
=
V
CC
R2
C2
C1
VCO
Loop Filter
Charge Pump
F s
( )
R
2
s
τ
(
s
τ
2
s
τ
1
1
+
)
------------------------------------------
=
τ
2
R
2
C
2
=
τ
1
R
2
C
C
2
C
1
+
C
2
------------------
=
ω
LBW
τ
1
τ
2
------------------
=
τ
1
--------------------------------------------------
)
ω
LBW
=
τ
2
ω
2
LBW
τ
1
--------------------------
=
相關PDF資料
PDF描述
RF2513 UHF TRANSMITTER
RF2514 VHF/UHF TRANSMITTER
RF2516 VHF/UHF TRANSMITTER
RF2601 GAIN CONTROLLED IF AMPLIFIER
RF2603 2.8V PCS UPCONVERTER
相關代理商/技術參數
參數描述
RF2513 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:UHF TRANSMITTER
RF2514 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER
RF2514_06 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER
RF2514_1 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER
RF2514PCBA 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:VHF/UHF TRANSMITTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*