- 您現在的位置：買賣IC網 > PDF目錄385770 > RF3320PCBA (RF Micro Devices, Inc.) CABLE REVERSE PATH PROGRAMMABLE GAIN AMPLIFIER PDF資料下載
參數資料
| 型號： | RF3320PCBA |
| 廠商： | RF Micro Devices, Inc. |
| 英文描述： | CABLE REVERSE PATH PROGRAMMABLE GAIN AMPLIFIER |
| 中文描述： | 電纜反向路徑可編程增益放大器 |
| 文件頁數： | 16/18頁 |
| 文件大?。?/td> | 318K |
| 代理商： | RF3320PCBA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁
Preliminary
3-42
RF3320
Rev A10 010514
3
L
A
Hardware Setup
Gain and Harmonic Distortion Test Setup
To test the gain of the RF3320 PCBA, connect a low-
pass or band-pass filter to the output of the signal gen-
erator. Use a filter just above the frequency you want to
test. The filter is used to attenuate any harmonics out-
put by the signal generator. Connect the signal genera-
tor to the power meter and measure the power.
Compare with modulation enabled and disabled to
make sure the meter was measuring average rather
than peak power. No more than 0.2dB difference in
power should be observed. An offset on the signal gen-
erator may be needed to match the level shown on the
power meter. The signal generator should then be con-
nected directly to a spectrum analyzer. Make sure the
output of the signal generator is the same as the input
read by the spectrum analyzer. Adjust the offset of the
spectrum analyzer until the signal out is the same as
the signal in on the spectrum analyzer. Turn off the RF
and modulation. Check positioning of the jumpers on
the board. Refer to the PCBA section of this applica-
tion note to verify proper positions. Connect the output
of the signal generator to J6: RFIN of the PCB. Con-
nect J7: RFOUT to the spectrum analyzer. Ensure that
you are accounting correctly for the losses in the 75
to 50
conversion at the output of the device; there is
an output voltage loss of 3.5dB for the evaluation
board in its standard configuration (see output stage
circuit description). Connect one end of the serial cable
into the computer and the other end into J1 of the PCB.
Connect +5.0V
DC
into V+ and ground into GND(JP1).
Turn on the DC power and turn on RF from the signal
generator. Set the GCW to 58 and make sure
TXEnable is checked. The amplified signal should be
displayed on the spectrum analyzer. The harmonics
can also be viewed with this setup. As you change the
GCW from 58 to 0 (in steps of one), there will be a 1dB
change in the output of the PCB.
ACPR Test Setup
To test the ACPR of the RF3320 PCBA set modulation
to:
QPSK
2Bits/Sym
160ksps
α
=0.25
PRBS-20bit Data
4
CLK Line
5
SHUTDOWN Line
3
Data Line
6
TX Enable Line
25 Pin D-Connector (Back View)
RF3320 PCBA Cable
2
CS Line
18
Ground
Figure 3. Cable Configuration
Figure 4. On-Screen Display
相關PDF資料 |
PDF描述 |
|---|---|
| RF3321PCBA | REVERSE PATH HIGH OUTPUT POWER PROGRAMMABLE GAIN AMPLIFIER |
| RF3321 | REVERSE PATH HIGH OUTPUT POWER PROGRAMMABLE GAIN AMPLIFIER |
| RF3322 | CABLE REVERSE PATH PROGRAMMABLE GAIN AMPLIFIER |
| RF3322PCBA | CABLE REVERSE PATH PROGRAMMABLE GAIN AMPLIFIER |
| RF3330 | IF GAIN CONTROLLED AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF3321 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:REVERSE PATH HIGH OUTPUT POWER PROGRAMMABLE GAIN AMPLIFIER |
| RF3321PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:REVERSE PATH HIGH OUTPUT POWER PROGRAMMABLE GAIN AMPLIFIER |
| RF3322 | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:CABLE REVERSE PATH PROGRAMMABLE GAIN AMPLIFIER |
| RF3322PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:CABLE REVERSE PATH PROGRAMMABLE GAIN AMPLIFIER |
| RF3323-000 | 制造商:TE Connectivity 功能描述:- Bag |
發布緊急采購，3分鐘左右您將得到回復。