- 您現在的位置：買賣IC網 > PDF目錄376314 > RR0816P-683-D (Electronic Theatre Controls, Inc.) 2-ch DC/DC Converter IC PDF資料下載
參數資料
| 型號： | RR0816P-683-D |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 2-ch DC/DC Converter IC |
| 中文描述： | 2通道直流/直流轉換器集成電路 |
| 文件頁數： | 12/36頁 |
| 文件大小： | 380K |
| 代理商： | RR0816P-683-D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
MB39A104
12
2.
Control Function
When CTL terminal (pin 24) is “L” level, IC becomes the standby mode. The power supply current is 10
μ
A (Max)
at the standby mode.
On/Off Setting Conditions
CTL
3.
Protective Functions
(1) Timer-latch overcurrent protection circuit block (OCP)
The timer-latch overcurrent protection circuit is actuated upon completion of the soft-start period. When an
overcurrent flows, the circuit detects the increase in the voltage between the FET’s drain and source using the
external FET ON resistor, actuates the timer circuit, and starts charging the capacitor C
SCP
con-nected to the
CSCP terminal (pin 8). If the overcurrent remains flowing beyond the predetermined period of time, latch is set
and OUT terminlas (pin 3,22) of each channel are fixed at “H” level. And the circuit sets the latch to turn off the
external FET. The detection current value can be set by resistor R
LIM1
connected between the FET’s drain and
the ILIM1 terminal (pin 5) and resistor R
LIM2
connected between the drain and the ILIM2 terminal (pin 20).
Changing connection enables to detect overcurrent at current sense resistor.
To reset the actuated protection circuit, either the power supply turn off and on again or set the CTL terminal
(pin 6) to the “L” level to lower the VREF terminal (pin 17) voltage to 2.4 V (Min) or less. (See “1. Setting Timer-
Latch Overcurrent Protection Detection Current” in “
I
ABOUT TIMER-LATCH PROTECTION CIRCUIT”.)
(2) Timer-latch short-circuit protection circuit (SCP Logic, SCP Comp.)
The short-circuit detection comparator (SCP Comp.) detects the output voltage level of Error Amp, and if the
error amp output voltage of any channel falls below the short-circuit detection voltage (3.1 V Typ), the timer
circuits are actuated to start charging the external capacitor C
SCP
connected to the CSCP terminal (pin 8).
When the capacitor voltage reaches about 0.73 V, the circuit is turned off the output transistor and sets the dead
time to 100 %.
To reset the actuated protection circuit, either the power supply turn off and on again or set the CTL terminal
(pin 24) to the “L” level to lower the VREF terminal (pin 17) voltage to 2.4 V (Min) or less. (See “2. Setting Time
Constant for Timer-Latch Short-Circuit Protection Circuit” in “
I
ABOUT TIMER-LATCH PROTECTION CIR-
CUIT”.)
(3) Under voltage lockout protection circuit (UVLO)
The transient state or a momentary decrease in supply voltage, which occurs when the power supply is turned
on, may cause the IC to malfunction, resulting in breakdown or degradation of the system. To prevent such
malfunctions, under voltage lockout protection circuit detects a decrease in internal reference voltage with respect
to the power supply voltage, turns off the output transistor, and sets the dead time to 100% while holding the
CSCP terminal (pin 8) at the “L” level.
The circuit restores the output transistor to normal when the supply voltage reaches the threshold voltage of the
undervoltage lockout protection circuit.
(4) Protection circuit operating function table
This table refers to output condition when protection circuit is operating.
Operating circuit
Power
L
OFF (Standby)
H
ON (Operating)
CS1
CS2
OUT1
OUT2
Overcurrent protection circuit
L
L
H
H
Short-circuit protection circuit
L
L
H
H
Under-voltage lockout
L
L
H
H
相關PDF資料 |
PDF描述 |
|---|---|
| RS-422 | RS-422 AND RS-485 APPLICATION NOTE |
| RS-485 | RS-422 AND RS-485 APPLICATION NOTE |
| RS-MK-X2010 | High Integrity FM Transceiver |
| RS3FS | SDR Cable Assembly; Connector Type A:micro D Ribbon Plug; Connector Type B:micro D Ribbon Plug; Cable Length:2m; No. of Contacts:26; Pitch Spacing:0.8mm RoHS Compliant: Yes |
| RS3FS | Damper Diodes (For TV) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RR0816P-683-D-C | 制造商:Susumu 功能描述:Resistor,Thin Film,SMD,1608,68K |
| RR0816P-6980-D-82A | 功能描述:薄膜電阻器 - SMD 1/16W 698ohm 0.5% 25ppm RoHS:否 制造商:AVX 電阻:50 Ohms 容差:2 % 溫度系數:150 PPM / C 封裝 / 箱體:2010 (5025 metric) 功率額定值:10 W 系列:RP9 電壓額定值: 工作溫度范圍:- 55 C to + 150 C 端接類型:SMD/SMT 尺寸:2.54 mm W x 5.08 mm L x 1.02 mm H 封裝:Reel |
| RR0816P-6981-D-82H | 功能描述:薄膜電阻器 - SMD 1/16W 6.98Kohm 0.5% 25ppm RoHS:否 制造商:AVX 電阻:50 Ohms 容差:2 % 溫度系數:150 PPM / C 封裝 / 箱體:2010 (5025 metric) 功率額定值:10 W 系列:RP9 電壓額定值: 工作溫度范圍:- 55 C to + 150 C 端接類型:SMD/SMT 尺寸:2.54 mm W x 5.08 mm L x 1.02 mm H 封裝:Reel |
| RR0816P-6982-D-82C | 功能描述:薄膜電阻器 - SMD 1/16W 69.8Kohm 0.5% 25ppm RoHS:否 制造商:AVX 電阻:50 Ohms 容差:2 % 溫度系數:150 PPM / C 封裝 / 箱體:2010 (5025 metric) 功率額定值:10 W 系列:RP9 電壓額定值: 工作溫度范圍:- 55 C to + 150 C 端接類型:SMD/SMT 尺寸:2.54 mm W x 5.08 mm L x 1.02 mm H 封裝:Reel |
| RR0816P-7150-D-83A | 功能描述:薄膜電阻器 - SMD 1/16W 715ohm 0.5% 25ppm RoHS:否 制造商:AVX 電阻:50 Ohms 容差:2 % 溫度系數:150 PPM / C 封裝 / 箱體:2010 (5025 metric) 功率額定值:10 W 系列:RP9 電壓額定值: 工作溫度范圍:- 55 C to + 150 C 端接類型:SMD/SMT 尺寸:2.54 mm W x 5.08 mm L x 1.02 mm H 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。