參數資料
型號： RS-485
廠商： Electronic Theatre Controls, Inc.
英文描述： RS-422 AND RS-485 APPLICATION NOTE
中文描述： RS - 422和RS - 485接口應用筆記
文件頁數： 4/44頁
文件大?。?/td> 628K
代理商： RS-485
RS-422/485 Application Note
1
B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350
PH (815) 433-5100 -- FAX (815) 434-7094
Chapter 1: Overview
Introduction
The purpose of this application note is to describe the main elements of
an RS-422 and RS-485 system. This application note attempts to cover
enough technical details so that the system designer will have considered all
the important aspects in his data system design. Since both RS-422 and RS-
485 are data transmission systems that use balanced differential signals, it is
appropriate to discuss both systems in the same application note. Throughout
this application note the generic terms of RS-422 and RS-485 will be used to
represent the EIA/TIA-422 and EIA/TIA-485 Standards.
Data Transmission Signals
Unbalanced Line Drivers
Each signal that transmits in an RS-232 unbalanced data transmission
system appears on the interface connector as a voltage with reference to a
signal ground. For example, the transmitted data (TD) from a DTE device
appears on pin 2 with respect to pin 7 (signal ground) on a DB-25 connector.
This voltage will be negative if the line is idle and alternate between that
negative level and a positive level when data is sent with a magnitude of
±
5 to
±
15 volts. The RS-232 receiver typically operates within the voltage range of
+3 to +12 and -3 to
-12 volts as shown in Figure 1.1.
Balanced Line Drivers
In a balanced differential system the voltage produced by the driver
appears across a pair of signal lines that transmit only one signal. Figure 1.2
shows a schematic symbol for a balanced line driver and the voltages that
exist. A balanced line driver will produce a voltage from 2 to 6 volts across
its A and B output terminals and will have a signal ground (C) connection.
Although proper connection to the signal ground is important, it isn't used by
a balanced line receiver in determining the logic state of the data line. A
balanced line driver can also have an input signal called an “Enable” signal.
The purpose of this signal is to connect the driver to its output terminals, A
and B. If the “Enable” signal is OFF, one can consider the driver as
disconnected from the transmission line. An RS-485 driver must have the
“Enable” control signal. An RS-422 driver may have this signal, but it is not
always required. The disconnected or "disabled" condition of the line driver
usually is referred to as the “tristate
1
” condition of the driver.
1
The term “tristate” comes from the fact that there is a third output state of an
RS-485 driver, in addition to the output states of “1” and “0.”
相關PDF資料
PDF描述
RS-MK-X2010 High Integrity FM Transceiver
RS3FS SDR Cable Assembly; Connector Type A:micro D Ribbon Plug; Connector Type B:micro D Ribbon Plug; Cable Length:2m; No. of Contacts:26; Pitch Spacing:0.8mm RoHS Compliant: Yes
RS3FS Damper Diodes (For TV)
RS4FS SDR Cable Assembly; Connector Type A:micro D Ribbon Plug; Connector Type B:micro D Ribbon Plug; Cable Length:5m; No. of Contacts:26; Pitch Spacing:0.8mm RoHS Compliant: Yes
RS8234 ServiceSAR Controller
相關代理商/技術參數
參數描述
RS485-232 制造商:PR 功能描述:
RS485-C1(AS) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RS232/RS485 CONV (AS)
RS485-C1(EU) 制造商:Equinox Technologies 功能描述:RS232/RS485 CONV (EU)
RS485-C1(UK) 制造商:Equinox Technologies 功能描述:RS232/RS485 CONV (UK)
RS485-C1(US) 制造商:Equinox Technologies 功能描述:RS232/RS485 CONV (US)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*