- 您現在的位置：買賣IC網 > PDF目錄26851 > S202SE1 (SHARP ELECTRONICS CORP) TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX PDF資料下載
參數資料
| 型號： | S202SE1 |
| 廠商： | SHARP ELECTRONICS CORP |
| 元件分類： | 繼電器，輸入/輸出模塊 |
| 英文描述： | TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX |
| 封裝： | PLASTIC, SIP-4 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 243K |
| 代理商： | S202SE1 |
8
S202SE1 Series
■ Design Considerations
In order for the SSR to turn off, the triggering current (lF) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.022F and Rs=47. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main out-
put triac as possible.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5Nm.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device sur-
face.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
● Design guide
Sheet No.: D4-A03201EN
● Recommended Operating Conditions
Parameter
Symbol
Unit
Input
Output
Input signal current at ON state
Input signal current at OFF state
Load supply voltage
Load supply current
Frequency
Operating temperature
IF(ON)
IF(OFF)
VOUT(rms)
IOUT(rms)
f
Topr
mA
V
mA
Hz
C
Locate snubber circuit between output terminals
(Cs
=0.022F, Rs=47)
Conditions
16
0
80
0.1
47
20
24
0.1
240
IT(rms)
×80%()
63
80
MIN.
MAX.
() See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
相關PDF資料 |
PDF描述 |
|---|---|
| S206CPW7-6VF-BP | SINGLE COLOR DISPLAY CLUSTER, WHITE, 5 mm |
| S206CUB500-14VAC-P | SINGLE COLOR DISPLAY CLUSTER, ULTRA BLUE, 5 mm |
| S206CR7-4VF-P | SINGLE COLOR DISPLAY CLUSTER, RED, 5 mm |
| S206CUB500-120VAC-P | SINGLE COLOR DISPLAY CLUSTER, ULTRA BLUE, 5 mm |
| S206CY3K-28VAC-BP | SINGLE COLOR DISPLAY CLUSTER, YELLOW, 5 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S202SE1F | 功能描述:固態繼電器-PCB安裝 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| S202SE2 | 功能描述:RELAY SSR 240VAC 8A ZC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S202 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
| S202SE2F | 功能描述:固態繼電器-PCB安裝 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| S-202T | 功能描述:穩流二極管 100V 2mA RoHS:否 制造商:Central Semiconductor 最大調節器電流:5.17 mA 最大極限電壓:2.9 V 最大峰值工作電壓:100 V 安裝風格:Through Hole 封裝 / 箱體:DO-204AH 封裝: |
| S202T01 | 功能描述:RELAY SSR 240VAC 2A TRIAC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S202 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
發布緊急采購，3分鐘左右您將得到回復。