- 您現在的位置：買賣IC網 > PDF目錄231009 > S29AL016D70BAI022 (SPANSION LLC) 1M X 16 FLASH 3V PROM, 70 ns, PBGA48 PDF資料下載
參數資料
| 型號： | S29AL016D70BAI022 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
| 封裝： | 8.15 X 6.15 MM, FBGA-48 |
| 文件頁數： | 27/55頁 |
| 文件大?。?/td> | 1809K |
| 代理商： | S29AL016D70BAI022 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
November 27, 2007 S29AL016D_00_A7
S29AL016D
33
Data
She e t
11.3
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete,
or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is
valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase
operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause
DQ6 to toggle. (The system may use either OE# or CE# to control the read cycles.) When the operation is
complete, DQ6 stops toggling.
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for
approximately 100 s, then returns to reading array data. If not all selected sectors are protected, the
Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are
protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-
suspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6
toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must
also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use
DQ7 (see DQ7: Data# Polling on page 31).
If a program address falls within a protected sector, DQ6 toggles for approximately 1 s after the program
command sequence is written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program
algorithm is complete.
Table 11.1 on page 35 shows the outputs for Toggle Bit I on DQ6. Figure 11.2 on page 34 shows the toggle
bit algorithm in flowchart form, and Reading Toggle Bits DQ6/DQ2 on page 34 explains the algorithm.
Figure 17.9 on page 45 shows the toggle bit timing diagrams. Figure 17.10 on page 46 shows the differences
between DQ2 and DQ6 in graphical form. See also the subsection on DQ2: Toggle Bit II on page 33.
11.4
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that
is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is
valid after the rising edge of the final WE# pulse in the command sequence.
DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure.
(The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the
sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is
actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus,
both status bits are required for sector and mode information. Refer to Table 11.1 on page 35 to compare
outputs for DQ2 and DQ6.
Figure 11.2 on page 34 shows the toggle bit algorithm in flowchart form, and the section Reading Toggle Bits
DQ6/DQ2 on page 34 explains the algorithm. See also the DQ6: Toggle Bit I on page 33 subsection.
Figure 17.9 on page 45 shows the toggle bit timing diagram. Figure 17.10 on page 46 shows the differences
between DQ2 and DQ6 in graphical form.
相關PDF資料 |
PDF描述 |
|---|---|
| S29AL016D70TAN013 | 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29AL016D90BFN013 | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| SRL91-17UGR2-BB99 | ROCKER SWITCH, SPDT, MOMENTARY, PANEL MOUNT |
| SRL91-13AAR2-BB99 | ROCKER SWITCH, SPDT, LATCHED, PANEL MOUNT |
| SRL91-13AGA3-BB9N | ROCKER SWITCH, SPDT, LATCHED, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29AL016D70BAI023 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY |
| S29AL016D70BFI010 | 制造商:Spansion 功能描述:IC SM FLASH 3V 16MB 70NS |
| S29AL016D70BFI010(E) | 制造商:Spansion 功能描述:Cut Tape |
| S29AL016D70BFI013 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY |
| S29AL016D70BFI020 | 制造商:Spansion 功能描述:IC SM FLASH 3V 16MB 70NS |
發布緊急采購，3分鐘左右您將得到回復。