參數資料
型號： S29GL032A10TAI012
廠商： Spansion Inc.
英文描述： 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
中文描述： 64兆，32兆和16兆位3.0伏只頁面模式閃存，含有200納米MirrorBit工藝技術
文件頁數： 57/95頁
文件大?。?/td> 2389K
代理商： S29GL032A10TAI012
September 10, 2007 S29GL-A_00_A11
S29GL-A
57
D a t a
S h e e t
Figure 9.2
Program Operation
Note
See
Table 10.2 on page 61
and
Table 10.1 on page 62
for program command sequence.
9.5
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from any non-suspended sector. When the Program
Suspend command is written during a programming process, the device halts the program operation within
15
μ
s maximum (5
μ
s typical) and updates the status bits. Addresses are not required when writing the
Program Suspend command.
After the programming operation is suspended, the system can read array data from any non-suspended
sector. The Program Suspend command may also be issued during a programming operation while an erase
is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend.
If a read is needed from the Secured Silicon Sector area (One-time Program area), then user must use the
proper command sequences to enter and exit this region. Note that the Secured Silicon Sector, autoselect,
and CFI functions are unavailable when a program operation is in progress.
The system may also write the autoselect command sequence when the device is in the Program Suspend
mode. The system can read as many autoselect codes as required. When the device exits the autoselect
mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See
Autoselect Command Sequence
on page 53
for more information.
After the Program Resume command is written, the device reverts to programming. The system can
determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard
program operation. See
Write Operation Status
on page 63
for more information.
The system must write the Program Resume command (address bits are don’t care) to exit the Program
Suspend mode and continue the programming operation. Further writes of the Resume command are
ignored. Another Program Suspend command can be written after the device resumes programming.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相關PDF資料
PDF描述
S29GL032A10TAI013 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL032A10TFI010 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL032A10TFI012 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL032A10TFI013 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL032A30BAI010 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
相關代理商/技術參數
參數描述
S29GL032A10TAI013 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology
S29GL032A10TAIR10 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 32MBIT 4MX8/2MX16 100NS 56TSOP - Trays
S29GL032A10TAIR11 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A10TAIR12 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
S29GL032A10TAIR13 制造商:SPANSION 制造商全稱:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*