- 您現在的位置：買賣IC網 > PDF目錄231009 > S29JL032H60TAI023 (ADVANCED MICRO DEVICES INC) 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 PDF資料下載
參數資料
| 型號： | S29JL032H60TAI023 |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 |
| 封裝： | MO-142DD, TSOP-48 |
| 文件頁數： | 31/66頁 |
| 文件大?。?/td> | 1691K |
| 代理商： | S29JL032H60TAI023 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
March 10, 2005 S29JL032H_00A11
S29JL032H
35
Ad vance
Info rmat i o n
Program Operations tables in the AC Characteristics section for parameters, and
Figure 19 section for timing diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is
initiated by writing two unlock cycles, followed by a set-up command. Two addi-
tional unlock cycles are written, and are then followed by the address of the
sector to be erased, and the sector erase command. Table 13 shows the address
and data requirements for the sector erase command sequence.
The device does not require the system to preprogram prior to erase. The Em-
bedded Erase algorithm automatically programs and verifies the entire sector for
an all zero data pattern prior to electrical erase. The system is not required to
provide any controls or timings during these operations.
After the command sequence is written, a sector erase time-out of 80 s occurs.
During the time-out period, additional sector addresses and sector erase com-
mands may be written. Loading the sector erase buffer may be done in any
sequence, and the number of sectors may be from one sector to all sectors. The
time between these additional cycles must be less than 80 s, otherwise erasure
may begin. Any sector erase address and command following the exceeded time-
out may or may not be accepted. It is recommended that processor interrupts be
disabled during this time to ensure all commands are accepted. The interrupts
can be re-enabled after the last Sector Erase command is written. Any com-
mand other than Sector Erase or Erase Suspend during the time-out
period resets that bank to the read mode. The system must rewrite the com-
mand sequence and any additional addresses and commands.
The system can monitor DQ3 to determine if the sector erase timer has timed out
(See the section on DQ3: Sector Erase Timer.). The time-out begins from the ris-
ing edge of the final WE# or CE# pulse (first rising edge) in the command
sequence.
When the Embedded Erase algorithm is complete, the bank returns to reading
array data and addresses are no longer latched. Note that while the Embedded
Erase operation is in progress, the system can read data from the non-erasing
bank. The system can determine the status of the erase operation by reading
DQ7, DQ6, DQ2, or RY/BY# in the erasing bank. Refer to the Write Operation Sta-
tus section for information on these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is
valid. All other commands are ignored. However, note that a hardware reset im-
mediately terminates the erase operation. If that occurs, the sector erase
command sequence should be reinitiated once that bank has returned to reading
array data, to ensure data integrity. Note that the SecSi Sector, autoselect, and
CFI functions are unavailable when an erase operation is in progress.
Program Operations tables in the AC Characteristics section for parameters, and
Figure 19 section for timing diagrams.
相關PDF資料 |
PDF描述 |
|---|---|
| S29AL016D70BAI022 | 1M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
| S29AL016D70TAN013 | 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29AL016D90BFN013 | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| SRL91-17UGR2-BB99 | ROCKER SWITCH, SPDT, MOMENTARY, PANEL MOUNT |
| SRL91-13AAR2-BB99 | ROCKER SWITCH, SPDT, LATCHED, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29JL032H60TAI210 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI211 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI212 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI213 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI220 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。