參數資料
型號: S29NS-P
廠商: Spansion Inc.
英文描述: MirrorBit Flash Family
中文描述: MirrorBit閃存系列
文件頁數: 45/86頁
文件大?。?/td> 2234K
代理商: S29NS-P
February 20, 2007 S29NS-P_00_A1
S29NS-P MirrorBit
TM
Flash Family
45
D a t a
S h e e t
( A d v a n c e
I n f o r m a t i o n )
the bank address and the data 90h. The second cycle need only contain the data 00h. The bank then returns
to the read mode.
The device offers accelerated program operations through the V
PP
input. When the system asserts V
HH
on
this input, the device automatically enters the Unlock Bypass mode. The system may then write the two-cycle
Unlock Bypass program command sequence. The device uses the higher voltage on the V
PP
input to
accelerate the operation.
Refer to the
Erase/Program Timing
section for parameters, and
Figures
10.12
and
10.13
for timing diagrams
Software Functions and Sample Code
The following are C source code examples of using the unlock bypass entry, program, and exit functions.
Refer to the
Spansion Low Level Driver User’s Guide
(
www.spansion.com
) for general information on
Spansion Flash memory software development guidelines.
/* Example: Unlock Bypass Entry Command
*( (UINT16 *)bank_addr + 0x555 ) = 0x00AA;
*( (UINT16 *)bank_addr + 0x2AA ) = 0x0055;
*( (UINT16 *)bank_addr + 0x555 ) = 0x0020;
/* At this point, programming only takes two write cycles.
/* Once you enter Unlock Bypass Mode, do a series of like
/* operations (programming or sector erase) and then exit
/* Unlock Bypass Mode before beginning a different type of
/* operations.
*/
/* write unlock cycle 1
/* write unlock cycle 2
/* write unlock bypass command
*/
*/
*/
*/
*/
*/
*/
*/
/* Example: Unlock Bypass Program Command
/* Do while in Unlock Bypass Entry Mode!
*( (UINT16 *)bank_addr + 0x555 ) = 0x00A0;
*( (UINT16 *)pa )
/* Poll until done or error.
/* If done and more to program, */
/* do above two cycles again.
*/
*/
/* write program setup command
/* write data to be programmed
*/
*/
= data;
*/
*/
/* Example: Unlock Bypass Exit Command */
*( (UINT16 *)base_addr + 0x000 ) = 0x0090;
*( (UINT16 *)base_addr + 0x000 ) = 0x0000;
Table 6.23
Unlock Bypass Entry
(LLD Function = lld_UnlockBypassEntryCmd)
Cycle
Description
Operation
Byte Address
Word Address
Data
1
Unlock
Write
Base + AAAh
Base + 555h
00AAh
2
Unlock
Write
Base + 554h
Base + 2AAh
0055h
3
Entry Command
Write
Base + AAAh
Base + 555h
0020h
Table 6.24
Unlock Bypass Program
(LLD Function = lld_UnlockBypassProgramCmd)
Cycle
Description
Operation
Byte Address
Word Address
Data
1
Program Setup Command
Write
Base + xxxh
Base +xxxh
00A0h
2
Program Command
Write
Program Address
Program Address
Program Data
Table 6.25
Unlock Bypass Reset
(LLD Function = lld_UnlockBypassResetCmd)
Cycle
Description
Operation
Byte Address
Word Address
Data
1
Reset Cycle 1
Write
Base + xxxh
Base +xxxh
0090h
2
Reset Cycle 2
Write
Base + xxxh
Base +xxxh
0000h
相關PDF資料
PDF描述
S29PL127N65GFWW02 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL127N 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL129N65GAWW02 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL129N65GAWW03 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL129N70GAW000 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
相關代理商/技術參數
參數描述
S29PL032J 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S29PL032J55BAI120 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 2M x 16bit 55ns 48-Pin FBGA Tray 制造商:Spansion 功能描述:FLASH PARALLEL - Trays
S29PL032J55BFI120 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 32MBIT 2MX16 55NS 48FBGA - Trays
S29PL032J60BFI120 制造商:Spansion 功能描述:
S29PL032J60BFI120(E) 制造商:Spansion 功能描述:Cut Tape