- 您現在的位置：買賣IC網 > PDF目錄378683 > SA56004FTK (NXP Semiconductors N.V.) +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms PDF資料下載
參數資料
| 型號： | SA56004FTK |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms |
| 封裝： | SA56004AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 11, 2005,;SA56004AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 11, 20 |
| 文件頁數： | 7/36頁 |
| 文件大?。?/td> | 197K |
| 代理商： | SA56004FTK |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
SA56004X_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 22 May 2008
7 of 36
NXP Semiconductors
SA56004X
Digital temperature sensor with overtemperature alarms
8. Local LOW setpoint (LLS) and Remote LOW temperature setpoints (RLSHB) at 0
°
C.
9. Conversion Rate register (CR) is set to 8h; the default value of about 16
conversions/s.
7.5 Starting conversion
Upon POR, the RUN/STOP bit 6 of the configuration register is zero (default condition),
then, the device will enter into its free-running operation mode in which the device A/D
converter is enabled and the measurement function is activated. In this mode, the device
cycles the measurements of the local and remote temperature automatically and
periodically. The conversion rate is defined by the programmable conversion rate stored in
the conversion rate register. It also performs comparison between readings and limits of
the temperature in order to set the flags and interruption accordingly at the end of every
conversion. Measured values are stored in the temp registers, results of the limit
comparisons are reflected by the status of the flag bits in the status register and the
interruption is reflected by the logical level of the ALERT and T_CRIT output. If the
power-on temperature limit is not suitable, the temp limit values could be written into the
limit registers during the busy-conversion duration of about 38 ms of the first conversion
after power-up. Otherwise, the status register must be read and the configuration bit 7
must be reset in order to recover the device from interruption caused by the undesired
temp limits.
7.6 Low power software standby mode
The device can be placed in a software standby mode by setting the RUN/STOP bit 6 in
the configuration register HIGH (logic 1). In standby, the free-running oscillator is stopped,
the supply current is less than 10
μ
A if there is no SMBus activity, all data in the registers
is retained. However, the SMBus is still active and reading and writing registers can still be
performed. A one-shot command will initiate a single conversion which has the same
effect as any conversion that occurs when the device is in its free-running mode. To
restore the device to free running mode, set the RUN/STOP bit 6 LOW (logic 0).
7.7 Temperature data format
The temperature data can only be read from the Local and Remote Temperature
registers; the setpoint registers (e.g., T_CRIT, LOW, HIGH) are read/write.
Both local and remote temperature reading data is represented by an 11-bit,
2’s complement word with the Least Significant Bit (LSB) = 0.125
°
C. The temperature
setpoint data for the remote channel is also represented by an 11-bit, 2’s complement
word with the LSB = 0.125
°
C. The temperature setpoint data for both the local channel
and the T_CRIT setpoints are represented by 8-bit, 2’s complement words with the
LSB =1.0
°
C. For 11-bit temp data, the data format is a left justified, 16-bit word available
in two 8-bit registers (high byte and low byte). For 8-bit temp data, the data is available in
a single 8-bit register (high byte only).
相關PDF資料 |
PDF描述 |
|---|---|
| SA56004HD | +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms |
| SA56004HDP | +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms |
| SA56004AD | +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms |
| SA56004FDP | +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms |
| SA56004BDP | +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA56004GD | 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SA56004GD,112 | 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SA56004GD,118 | 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SA56004GDP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1 Degrees Celcious accurate, SMBus-compatible, 8-pin, remote/local digital temperature sensor with over temperature alarms |
| SA56004GDP,118 | 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。