參數資料
型號： SA56004HD
廠商： NXP Semiconductors N.V.
元件分類： 工業控制
英文描述： +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
封裝： SA56004AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 11, 2005,;SA56004AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 11, 20
文件頁數： 17/36頁
文件大?。?/td> 197K
代理商： SA56004HD
SA56004X_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 22 May 2008
17 of 36
NXP Semiconductors
SA56004X
Digital temperature sensor with overtemperature alarms
Event F
: Three consecutive measurements have been made with the remote
temperature below the RCS
TH threshold; the T_CRIT output is de-activated (goes
HIGH).
Event G
: The remote temp falls below the Remote LOW setpoint.
Event H
: Three consecutive measurements are made with the temp below the Remote
LOW setpoint; ALERT output is activated (goes LOW).
Event I
: The ALERT output is de-activated (goes HIGH) after a above_low_limit
temperature measurement is completed.
7.9.4
Remote diode selection
To measure the remote temperature or the temperature of an externally attached diode,
the device automatically forces two successive currents of about 160
μ
A and 10
μ
A at D+
pin. It measures the voltage (V
BE
) between D+ and D
, detects the difference between the
two V
BE
voltages or the
V
BE
and then converts the
V
BE
into a temperature data using
the basic PTAT voltage formula as shown in
Equation 1
. The device typically takes about
38 ms to perform a measurement during each conversion period or cycle, which is
selectable by programming the conversion rate register.
(1)
Where:
n = diode ideality factor
k = Boltzmann’s constant
T = absolute temperature (
°
K) = 273
°
C + T (
°
C)
q = electron charge
ln = natural logarithm
l2, l1 = two source currents
Because the device does not directly convert the sensed V
BE
as in the old method of
temperature measurement systems, the V
BE
calibration is not required. Furthermore, the
device remote temperature error is adjusted at the manufacturer to meet the specifications
with the use of the reference diode-connected transistors such as the 2N3904/2N3906.
The diode type to be used in customer applications must have the characteristics as close
to the 2N3904/2N3906 as possible in order to obtain optimal results. Finally, to prevent the
effects of system noise on the measured V
BE
signals, an external capacitor of about
2200 pF connected between the D+ and D
pins as well as the grounded-shield cable for
the diode connection wires are recommended.
7.9.5
Diode fault detection
The SA56004X is designed with circuitry to detect the fault conditions of the remote diode.
When the D+ pin is shorted to V
DD
or floating, the Remote Temperature High Byte (RTHB)
register is loaded with +127
°
C, the Remote Temperature Low Byte (RTLB) register is
loaded with 0
°
C, and the OPEN bit (bit 2 of the Status register) is set. Under the above
conditions of D+ shorted to V
DD
or floating, if the Remote T_CRIT setpoint is set less than
+127
°
C, and T_CRIT Mask are disabled, then, the T_CRIT output pins will be pulled
V
BE
n
q
------
×
l1
----
ln
×
=
相關PDF資料
PDF描述
SA56004HDP +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004AD +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004FDP +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004BDP +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
SA56004CDP +--1 deg Cel accurate, SMBus-compatible, 8-pin, remote-local digital temperature sensor with overtemperature alarms
相關代理商/技術參數
參數描述
SA56004HD,112 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
SA56004HD,118 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
SA56004HDP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1 Degrees Celcious accurate, SMBus-compatible, 8-pin, remote/local digital temperature sensor with over temperature alarms
SA56004HDP,118 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
SA56004HDP-T 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND REM +/- 1OC TS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*